1.INSTALL HOLE PLUG
Install the 4 hole plugs to the front suspension crossmember sub-assembly.
There are 2 different shapes of hole plug.
51228G
2.INSTALL FRONT SUSPENSION MEMBER PLATE
Install the 2 front suspension member plates to the front suspension crossmember sub-assembly.
12363A
3.INSTALL ENGINE MOVING CONTROL ROD
Install the engine moving control rod to the front suspension crossmember sub-assembly with the bolt.
48069
4.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.
48068
5.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
48811
6.INSTALL FRONT STABILIZER BAR
48829A
7.INSTALL FRONT NO. 1 STABILIZER BRACKET LH
48824A
8.INSTALL FRONT NO. 1 STABILIZER BRACKET RH
Perform the same procedure as for the LH side.
9.INSTALL STEERING LINK ASSEMBLY
Install the steering link assembly to the front suspension crossmember sub-assembly with the 2 bolts and 2 new nuts.
Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
Make sure to tighten the bolts starting from the left side of the vehicle.
51201
10.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Slowly jack up the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.
The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.
If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments to keep the front suspension crossmember sub-assembly level.
Install the front suspension crossmember sub-assembly to the vehicle body with the 6 bolts.
Lower the engine lifter.
Install the engine moving control rod with the bolt.
Install the 2 wire harness clamp brackets to the front suspension crossmember sub-assembly with the 2 bolts.
48069
11.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Install the front lower No. 1 suspension arm sub-assembly LH to the front lower ball joint assembly LH with the bolt and 2 nuts.
48068
12.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
45047
13.CONNECT TIE ROD END SUB-ASSEMBLY LH
45046
14.CONNECT TIE ROD END SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
43215
15.INSTALL STEERING KNUCKLE SEAL (w/ Seal)
48810
16.CONNECT FRONT STABILIZER LINK ASSEMBLY LH
Connect the front stabilizer link assembly LH to the front shock absorber assembly with the nut.
Do not damage the boot of the ball joint.
If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.
Install the cap.
48820B
17.CONNECT FRONT STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
51108A
18.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
Install the rear side rail reinforcement sub-assembly LH to the front suspension crossmember sub-assembly and vehicle body with the 4 bolts.
51107A
19.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
45025D
20.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
45260
21.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
22.INSTALL COLUMN HOLE COVER SILENCER SHEET
23.INSTALL FRONT WHEELS
24.STABILIZE SUSPENSION
48069
25.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
26.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
58166
27.INSTALL FRONT FLOOR COVER LH (w/ Cover)
58165B
28.INSTALL FRONT FLOOR COVER RH (w/ Cover)
Use the same procedure as for the LH side.
51444A
29.INSTALL REAR ENGINE UNDER COVER LH
51443C
30.INSTALL REAR ENGINE UNDER COVER RH
51441
31.INSTALL NO. 1 ENGINE UNDER COVER
32.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
33.INITIALIZATION HEADLIGHT ECU SUB-ASSEMBLY