Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER › from 2019.09
RM32K0E _53 Suspension _061339 REAR SUSPENSION _0299705 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.

Install the 7 hole plugs to the rear suspension member sub-assembly as shown in the illustration.


Hide 51284 2.INSTALL REAR SUSPENSION MEMBER HOLE COVER

a.

Install the 4 rear suspension member hole covers to the rear suspension member sub-assembly.


Hide 51249A 3.INSTALL REAR SUSPENSION MEMBER DAMPER

a.

Install the rear suspension member damper to the rear suspension member sub-assembly with the 2 bolts.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 48790 4.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 5.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51206A 6.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C365600C01
1.938,3.479 2.188,2.885 true 2.281,3.344 2.604,3.344 true 3.021,4.063 2.75,3.844 true 1.094,3.844 1.26,3.656 true 0.417,3.938 0.521,3.771 true 3.052,3.99 3.313,4.188 0.26,0.198 10 false *a 0.281,3.969 0.542,4.167 0.26,0.198 10 true *b 0.938,3.885 1.198,4.083 0.26,0.198 10 true *b 2.656,3.208 2.917,3.406 0.26,0.198 10 true *b 2.219,2.667 2.479,2.865 0.26,0.198 10 true *b
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
C345782

·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:
·

Use attachments and wooden blocks to keep the rear suspension member sub-assembly level.

·

Keep supporting the rear suspension member sub-assembly until the installation has been completed.




b.

Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle.


c.

Install the rear suspension member sub-assembly with the 2 bolts and 2 nuts.

Torque:
143 N*m (1458 kgf*cm, 105 ft.*lbf)


d.

w/ Height Control Sensor:

i.

Engage the clamp to install the height control sensor wire harness.



Hide 48790 7.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

a.

Temporarily install the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




Hide 48770A 8.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 9.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 10.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 11.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 12.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48258C 13.INSTALL REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 14.INSTALL REAR LOWER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 48231B 15.INSTALL REAR COIL SPRING LH

Hide 48231A 16.INSTALL REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 17.INSTALL REAR STABILIZER BAR

Hide 89408C 18.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

Hide 47319F 19.CONNECT REAR FLEXIBLE HOSE LH

a.

Connect the rear flexible hose LH to the flexible hose bracket with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 47318F 20.CONNECT REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as for the LH side.


Hide 48840A 22.INSTALL REAR STABILIZER LINK ASSEMBLY LH

Hide 48830D 23.INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 24.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 25.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 26.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.
C365323

Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48730F 27.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48790 28.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

a.

Install the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48770A 29.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 57628C 30.INSTALL REAR FLOOR SIDE MEMBER COVER LH

Hide 57627A 31.INSTALL REAR FLOOR SIDE MEMBER COVER RH

Hide 58165B 33.INSTALL FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the LH side.


Hide 17430 34.INSTALL TAIL EXHAUST PIPE ASSEMBLY

Hide 35.INSTALL REAR WHEEL

Hide 48740F 36.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

a.

Install the rear No. 2 suspension arm assembly LH (rear suspension member sub-assembly side) with the nut.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 48730F 37.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 39.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 41.PERFORM CALIBRATION

·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
Panoramic view monitor system (Click here)