The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub bolt removal/installation are shown below.
When removing or installing the rear disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISABLE BRAKE CONTROL
for TMC Made:
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMC Made)>REMOVAL
for TMMT Made:
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMMT Made)>REMOVAL
3.REMOVE REAR WHEEL
4.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
Disconnect the No. 2 parking brake wire assembly connector.
Remove the bolt and separate the rear flexible hose from the rear flexible hose bracket.
Remove the 2 bolts and separate the rear disc brake caliper assembly from the rear axle carrier sub-assembly.
Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.
42431
5.REMOVE REAR DISC
for TMC Made:
Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMC Made)>REMOVAL
for TMMT Made:
Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMMT Made)>REMOVAL
42312E
6.REMOVE REAR AXLE HUB BOLT
| *a | Service Nut |
Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Install the service nuts to prevent damage to the rear axle hub bolts.
Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.
Do not damage the threads of the rear axle hub bolts.
42312E
7.INSTALL REAR AXLE HUB BOLT
| *a | Service Nut |
| *b | Washer |
Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.
Install a washer and service nut to the rear axle hub bolt as shown in the illustration.
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Recommended washer thickness is 5 mm (0.197 in.) or more.
Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.
Install the service nuts to prevent damage to the rear axle hub bolts.
Do not damage the threads of the rear axle hub bolts.
Remove the 3 service nuts and washer from the 3 rear axle hub bolts.
42431
8.INSTALL REAR DISC
for TMC Made:
Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMC Made)>INSTALLATION
for TMMT Made:
Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMMT Made)>INSTALLATION
9.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.
Install the rear flexible hose to the rear flexible hose bracket with the bolt.
Connect the No. 2 parking brake wire assembly connector.
10.INSTALL REAR WHEEL
11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Connect the reservoir level switch connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION
Turn the power switch on (READY).
Depress the brake pedal and release it.
Clear the DTCs.