Home › Brake › BRAKE (REAR) › REAR BRAKE (for TMC Made) › 2019.09–2020.08
RM32K0E _54 Brake _060047 BRAKE (REAR) _0407396 REAR BRAKE(for TMC Made) A

BRAKE (REAR)  REAR BRAKE(for TMC Made)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear disc brake cylinder assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>PRECAUTION



Hide 2.PERFORM REAR BRAKE PAD REPLACEMENT MODE

Hide 5.REMOVE REAR WHEEL

Hide 6.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47319F 7.SEPARATE REAR FLEXIBLE HOSE

a.
C399537

Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.


Hide 890C0A 8.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C399528

Disconnect the No. 2 parking brake wire assembly from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the connector before performing this work.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




Hide 46310B 9.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY

a.
C422644

Using a 5 mm hexagon socket wrench, remove the 2 bolts and parking brake actuator assembly from the rear disc brake cylinder assembly.

NOTICE:
·

Check that there are no brake fluid leaks from the back of the rear disc brake cylinder assembly.

·

If there are any brake fluid leaks, replace the rear disc brake cylinder assembly.




b.

Remove the O-ring from the rear disc brake cylinder assembly.


Hide 10.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C422645C01
1.646,2.813 1.958,3.01 0.313,0.198 10 false *a 0.896,2.906 1.208,3.104 0.313,0.198 10 false *b
*a Turn
*b Hold


Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and rear disc brake cylinder assembly.


Hide 11.REMOVE REAR DISC BRAKE PAD

a.
C399540

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 12.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 13.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

a.
C366005

Remove the 4 rear disc brake pad support plates from the rear disc brake cylinder mounting.

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



Hide 14.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C399542C01
2.583,1.667 2.458,1.417 true 2.313,0.531 2.188,0.281 true 2.583,1.708 2.833,1.917 0.25,0.208 10 true *1 2.323,0.583 2.521,0.823 0.198,0.24 10 true *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear No. 2 Disc Brake Cylinder Slide Pin


Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.


b.
C406519C01
2.135,1.333 2.552,0.917 false 2.583,0.76 2.896,0.917 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 2 disc brake cylinder slide pin.

NOTICE:

Do not damage the rear No. 2 disc brake cylinder slide pin.



Hide 15.REMOVE REAR DISC BRAKE BUSHING DUST BOOT

a.
C399544

Remove the 2 rear disc brake bushing dust boots from the rear disc brake cylinder mounting.


Hide 16.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C422646

Remove the 2 bolts and rear disc brake cylinder mounting from the rear axle carrier sub-assembly.


Hide 42431 17.REMOVE REAR DISC

a.
C366010C01
0.99,1.927 1.51,1.5 true 0.979,1.927 1.49,1.448 true 0.823,1.854 1.135,2.01 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the rear disc and rear axle hub and bearing assembly.


b.

Remove the rear disc from the rear axle hub and bearing assembly.