Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER › 2019.09–2020.08
RM32K0E _52 Drivetrain _061337 AXLE AND DIFFERENTIAL _0299681 REAR AXLE CARRIER A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When removing or installing the rear disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

a.
C345053

Temporarily install the rear axle carrier sub-assembly to the rear upper control arm assembly with the bolt and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




b.

Temporarily install the rear shock absorber assembly to the rear axle carrier sub-assembly with the nut.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



c.

Install the rear trailing arm assembly to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
135 N*m (1377 kgf*cm, 100 ft.*lbf)


Hide 2.INSTALL FLEXIBLE HOSE BRACKET

a.

Install the flexible hose bracket to the rear axle carrier sub-assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 48720A 3.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 48258C 4.INSTALL REAR LOWER COIL SPRING INSULATOR

Hide 48231B 5.INSTALL REAR COIL SPRING

Hide 48790 7.INSTALL REAR UPPER CONTROL ARM ASSEMBLY

a.

Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt.

Torque:
73 N*m (744 kgf*cm, 54 ft.*lbf)

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.



Hide 48720A 8.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 48740F 9.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Install the rear No. 2 suspension arm assembly (rear axle carrier sub-assembly side) with the bolt.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 48540 10.INSTALL REAR SHOCK ABSORBER ASSEMBLY

Hide 48840A 11.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 42450B 12.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

Hide 13.CONNECT SKID CONTROL SENSOR WIRE

Hide 42431 14.INSTALL REAR DISC

Hide 15.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

Hide 89408C 16.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

Hide 17.INSTALL REAR WHEEL

Hide 48740F 18.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

a.

Install the rear No. 2 suspension arm assembly (rear suspension member sub-assembly side) with the nut.

Click hereSuspension>REAR SUSPENSION>REAR LOWER ARM>INSTALLATION


Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION


c.

Turn the power switch on (READY).


d.

Depress the brake pedal and release it.



Hide 20.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 22.PERFORM INITIALIZATION (w/ Height Control Sensor)