Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BACK DOOR OUTSIDE GARNISH › from 2019.09
RM32K0E _59 Vehicle Exterior _061792 EXTERIOR PANELS / TRIM _0304189 BACK DOOR OUTSIDE GARNISH A

EXTERIOR PANELS / TRIM  BACK DOOR OUTSIDE GARNISH  REASSEMBLY  


PROCEDURE

Hide 75431A 1.INSTALL NO. 1 BACK DOOR EMBLEM

Hide 75443 2.INSTALL NO. 3 BACK DOOR NAME PLATE

Hide 75442A 3.INSTALL NO. 2 BACK DOOR NAME PLATE

Hide 75441E 4.INSTALL NO. 1 BACK DOOR NAME PLATE

Hide 76819 5.INSTALL BACK DOOR OUTSIDE GARNISH SEAL

HINT:
·

Using the same procedure, install every back door outside garnish seal.

·

When installing the back door outside garnish seal, heat the back door outside garnish sub-assembly using a heat light.



Heating Temperature:
Item Temperature
Back Door Outside Garnish Sub-assembly 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the back door outside garnish sub-assembly excessively.


a.

Clean the back door outside garnish sub-assembly surface.

i.

Using a heat light, heat the back door outside garnish sub-assembly surface.


ii.

Remove the double-sided tape from the back door outside garnish sub-assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish sub-assembly.


c.

Remove the release paper from a new back door outside garnish seal.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B458874C01
1.563,1.708 2.031,1.188 2.031,1.188 1.615,1.74 true 2.104,1.063 2.344,1.26 0.24,0.198 10 true *1 1.521,1.875 1.76,2.073 0.24,0.198 10 true *a
*1 Mark-off Line
*a 1.5 mm (0.05905 in.)


Install the back door outside garnish seal as shown in the illustration.

HINT:

Align the back door outside garnish seal with the mark-off line of the back door outside garnish sub-assembly.



Hide 76821 6.INSTALL UPPER BACK DOOR GARNISH MOULDING PROTECTOR

HINT:
·

Using the same procedure, install every upper back door garnish moulding protector.

·

When installing the upper back door garnish moulding protector, heat the back door outside garnish sub-assembly using a heat light.



Heating Temperature:
Item Temperature
Back Door Outside Garnish Sub-assembly 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the back door outside garnish sub-assembly excessively.


a.

Clean the back door outside garnish sub-assembly surface.

i.

Using a heat light, heat the back door outside garnish sub-assembly surface.


ii.

Remove the double-sided tape from the back door outside garnish sub-assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish sub-assembly.


c.

Remove the release paper from a new upper back door garnish moulding protector.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

for TMMT Made:

i.
B458875C01
0.979,1.375 0.552,1.792 0.552,1.792 0.938,1.313 true 2.563,1.271 2.948,1.656 2.948,1.656 2.49,1.271 true 0.375,1.74 0.688,1.938 0.313,0.198 10 false *1 2.917,1.698 3.229,1.896 0.313,0.198 10 false *1 0.896,0.969 1.135,1.167 0.24,0.198 10 true *a 2.438,0.917 2.656,1.115 0.219,0.198 10 true *b
*1 Mark-off Line
*a 1.0 mm (0.0393 in.)
*b 5.0 mm (0.196 in.)


Install the upper back door garnish moulding protector as shown in the illustration.

HINT:

Align the upper back door garnish moulding protector with the mark-off line of the back door outside garnish sub-assembly.




e.

for TMC Made:

i.
B558072C01
0.979,1.375 0.552,1.792 0.552,1.792 0.938,1.313 true 2.531,1.26 2.948,1.656 2.948,1.656 2.5,1.333 true 0.375,1.74 0.688,1.938 0.313,0.198 10 false *1 2.917,1.698 3.229,1.896 0.313,0.198 10 false *1 0.896,0.969 1.135,1.167 0.24,0.198 10 true *a 2.438,0.917 2.656,1.115 0.219,0.198 10 true *b
*1 Mark-off Line
*a 1.0 mm (0.0393 in.)
*b 1.0 mm (0.0393 in.)


Install the upper back door garnish moulding protector as shown in the illustration.

HINT:

Align the upper back door garnish moulding protector with the mark-off line of the back door outside garnish sub-assembly.




Hide 76822 7.INSTALL LOWER BACK DOOR GARNISH MOULDING PROTECTOR

HINT:
·

Using the same procedure, install every lower back door garnish moulding protector.

·

When installing the lower back door garnish moulding protector, heat the back door outside garnish sub-assembly using a heat light.



Heating Temperature:
Item Temperature
Back Door Outside Garnish Sub-assembly 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the back door outside garnish sub-assembly excessively.


a.

Clean the back door outside garnish sub-assembly surface.

i.

Using a heat light, heat the back door outside garnish sub-assembly surface.


ii.

Remove the double-sided tape from the back door outside garnish sub-assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish sub-assembly.


c.

Remove the release paper from a new lower back door garnish moulding protector.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.

for TMMT Made:

i.
B458876C01
1.865,0.427 2.021,0.75 2.021,0.75 1.917,0.354 true 1.25,1.833 1.708,2.021 1.708,2.021 1.344,1.802 true 2.167,0.271 2.375,0.469 0.208,0.198 10 true *a 2,0.792 2.208,0.99 0.208,0.198 10 true *1 1.771,1.917 1.979,2.115 0.208,0.198 10 true *1 0.875,1.729 1.083,1.927 0.208,0.198 10 false *b
*1 Mark-off Line
*a 5.0 mm (0.196 in.)
*b 1.0 mm (0.0393 in.)


Install the lower back door garnish moulding protector as shown in the illustration.

HINT:

Align the lower back door garnish moulding protector with the mark-off line of the back door outside garnish sub-assembly.




e.

for TMC Made:

i.
B558073C01
1.865,0.427 2.021,0.75 2.021,0.75 1.948,0.385 true 1.25,1.833 1.708,2.021 1.708,2.021 1.344,1.802 true 2.125,0.292 2.333,0.49 0.208,0.198 10 true *a 2,0.792 2.208,0.99 0.208,0.198 10 true *1 1.771,1.917 1.979,2.115 0.208,0.198 10 true *1 0.875,1.729 1.083,1.927 0.208,0.198 10 false *b
*1 Mark-off Line
*a 1.0 mm (0.0393 in.)
*b 1.0 mm (0.0393 in.)


Install the lower back door garnish moulding protector as shown in the illustration.

HINT:

Align the lower back door garnish moulding protector with the mark-off line of the back door outside garnish sub-assembly.




Hide 76825D 8.INSTALL NO. 1 BACK DOOR OUTSIDE GARNISH PROTECTOR

HINT:
·

Using the same procedure, install every No. 1 back door outside garnish protector.

·

When installing the No. 1 back door outside garnish protector, heat the back door outside garnish sub-assembly using a heat light.



Heating Temperature:
Item Temperature
Back Door Outside Garnish Sub-assembly 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the back door outside garnish sub-assembly excessively.


a.

Clean the back door outside garnish sub-assembly surface.

i.

Using a heat light, heat the back door outside garnish sub-assembly surface.


ii.

Remove the double-sided tape from the back door outside garnish sub-assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the back door outside garnish sub-assembly.


c.

Remove the release paper from a new No. 1 back door outside garnish protector.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B458878C01
1.948,1.302 2.333,0.844 2.333,0.844 2,1.375 true 1.49,1.573 1.052,0.958 1.052,0.958 1.5,1.385 true 2.365,0.688 2.677,0.885 0.313,0.198 10 false *1 0.917,0.781 1.229,0.979 0.313,0.198 10 false *1 1.49,1.813 1.802,2.01 0.313,0.198 10 false *a 1.958,1.552 2.271,1.75 0.313,0.198 10 false *a
*1 Mark-off Line
*a 1.5 mm (0.05905 in.)


Install the No. 1 back door outside garnish protector as shown in the illustration.

HINT:

Align the No. 1 back door outside garnish protector with the mark-off line of the back door outside garnish sub-assembly.



Hide 76824 9.INSTALL BACK DOOR GARNISH MOULDING PROTECTOR LH

HINT:

When installing the back door garnish moulding protector LH, heat the back door outside garnish sub-assembly and No. 2 back door outside garnish using a heat light.


Heating Temperature:
Item Temperature
Back Door Outside Garnish Sub-assembly and No. 2 Back Door Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the back door outside garnish sub-assembly and No. 2 back door outside garnish excessively.


a.

for Back Door Outside Garnish Side:

i.

Clean the back door outside garnish sub-assembly surface.

1.

Using a heat light, heat the back door outside garnish sub-assembly surface.

2.

Remove the double-sided tape from the back door outside garnish sub-assembly.

3.

Wipe off any tape adhesive residue with cleaner.



ii.

Using a heat light, heat the back door outside garnish sub-assembly.


iii.

Remove the release paper from a new back door garnish moulding protector LH.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iv.
B458881C01
2.146,0.281 1.667,0.521 1.667,0.521 2.167,0.198 true 1.521,1.708 2.396,1.042 2.396,1.042 2.021,0.823 true 1.458,0.51 1.677,0.719 0.219,0.208 10 true *1 1.698,0.052 1.917,0.26 0.219,0.208 10 true *b 2.458,0.938 2.677,1.146 0.219,0.208 10 false *a
*1 Mark-off Line
*a Scribed Line
*b 1.0 mm (0.0393 in.)


Install the back door garnish moulding protector LH as shown in the illustration.

HINT:

Align the back door garnish moulding protector LH with the mark-off line of the back door outside garnish sub-assembly.




b.

for No. 2 Back Door Outside Garnish:

i.

Clean the No. 2 back door outside garnish surface.

1.

Using a heat light, heat the No. 2 back door outside garnish surface.

2.

Remove the double-sided tape from the No. 2 back door outside garnish.

3.

Wipe off any tape adhesive residue with cleaner.



ii.

Using a heat light, heat the No. 2 back door outside garnish.


iii.

Remove the release paper from a new back door garnish moulding protector LH.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iv.
B465621C01
1.396,1.5 1.292,1.938 1.292,1.938 2.542,1.177 false 1.198,1.938 1.51,2.094 0.313,0.156 10 false *a
*a Scribed Line


Install the back door garnish moulding protector LH as shown in the illustration.

HINT:

Install each back door garnish moulding protector LH along the line on the No. 2 back door outside garnish.




Hide 76823 10.INSTALL BACK DOOR GARNISH MOULDING PROTECTOR RH

HINT:

Use the same procedure as for the LH side.


Hide 76822B 11.INSTALL BACK DOOR GARNISH SIDE PROTECTOR LH (for Type B)

HINT:

When installing the back door garnish side protector LH, heat the back No. 2 back door outside garnish using a heat light.


Heating Temperature:
Item Temperature
No. 2 Back Door Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 2 back door outside garnish excessively.


a.

Clean the No. 2 back door outside garnish surface.

i.

Using a heat light, heat the No. 2 back door outside garnish surface.


ii.

Remove the double-sided tape from the No. 2 back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the No. 2 back door outside garnish.


c.

Remove the release paper from a new back door garnish side protector LH.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B557817C01
1.167,1.948 1.042,1.625 false 1.167,1.948 1.479,2.146 0.313,0.198 10 false *a
*a Scribed Line


Install the back door garnish side protector LH as shown in the illustration.

HINT:

Install each back door garnish side protector LH along the line on the No. 2 back door outside garnish.



Hide 76821B 12.INSTALL BACK DOOR GARNISH SIDE PROTECTOR RH (for Type B)

HINT:

Use the same procedure as for the LH side.


Hide 76825E 13.INSTALL NO.2 BACK DOOR OUTSIDE GARNISH PROTECTOR (for Type A)

HINT:

When installing the No. 2 back door outside garnish protector, heat the back No. 2 back door outside garnish using a heat light.


Heating Temperature:
Item Temperature
No. 2 Back Door Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 2 back door outside garnish excessively.


a.

Clean the No. 2 back door outside garnish surface.

i.

Using a heat light, heat the No. 2 back door outside garnish surface.


ii.

Remove the double-sided tape from the No. 2 back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the No. 2 back door outside garnish.


c.

Remove the release paper from a new No. 2 back door outside garnish protector.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B458879C01
0.417,0.969 0.292,0.646 false 3.01,0.958 3.146,0.635 false 3.208,0.542 3.396,0.719 0.188,0.177 10 false *a 0.094,0.542 0.406,0.74 0.313,0.198 10 false *a
*a Scribed Line


Install the No. 2 back door outside garnish protector as shown in the illustration.

HINT:

Install each No. 2 back door outside garnish protector along the line on the No. 2 back door outside garnish.



Hide 76825E 14.INSTALL NO.2 BACK DOOR OUTSIDE GARNISH PROTECTOR (for Type B)

HINT:

When installing the No. 2 back door outside garnish protector, heat the No. 2 back door outside garnish using a heat light.


Heating Temperature:
Item Temperature
No. 2 Back Door Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 2 back door outside garnish excessively.


a.

Clean the No. 2 back door outside garnish surface.

i.

Using a heat light, heat the No. 2 back door outside garnish surface.


ii.

Remove the double-sided tape from the No. 2 back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the No. 2 back door outside garnish.


c.

Remove the release paper from a new No. 2 back door outside garnish protector.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter..



d.
B557979C01
0.229,1.115 0.708,0.594 false 2.823,0.583 3.219,1.115 false 2.677,0.427 2.99,0.583 0.313,0.156 10 false *a 0.708,0.469 1.021,0.625 0.313,0.156 10 false *a
*a Scribed Line


Install the No. 2 back door outside garnish protector as shown in the illustration.

HINT:

Install each No. 2 back door outside garnish protector along the line on the No. 2 back door outside garnish.



Hide 76825 15.INSTALL BACK DOOR OUTSIDE GARNISH PROTECTOR LH (for Type B)

HINT:

When installing the back door outside garnish protector LH, heat the back No. 2 back door outside garnish using a heat light.


Heating Temperature:
Item Temperature
No. 2 Back Door Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 2 back door outside garnish excessively.


a.

Clean the No. 2 back door outside garnish surface.

i.

Using a heat light, heat the No. 2 back door outside garnish surface.


ii.

Remove the double-sided tape from the No. 2 back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the No. 2 back door outside garnish.


c.

Remove the release paper from a new back door outside garnish protector LH.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B558064C01
0.844,1.094 1.188,0.844 true 0.688,1.042 1,1.24 0.313,0.198 10 false *a
*a Scribed Line


Install the back door outside garnish protector LH as shown in the illustration.

HINT:

Install each back door outside garnish protector LH along the line on the No. 2 back door outside garnish.



Hide 76825 16.INSTALL BACK DOOR OUTSIDE GARNISH PROTECTOR RH (for Type B)

HINT:

Use the same procedure as for the LH side.


Hide 76825 17.INSTALL BACK DOOR OUTSIDE GARNISH PROTECTOR (for Type A)

HINT:

When installing the back door outside garnish protector, heat the No. 2 back door outside garnish using a heat light.


Heating Temperature:
Item Temperature
No. 2 Back Door Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 2 back door outside garnish excessively.


a.

for TMMT Made:

i.

Clean the No. 2 back door outside garnish surface.

1. Using a heat light, heat the No. 2 back door outside garnish surface.

2. Remove the double-sided tape from the No. 2 back door outside garnish.

3. Wipe off any tape adhesive residue with cleaner.



ii.

Using a heat light, heat the No. 2 back door outside garnish.


iii.

Remove the release paper from a new back door outside garnish protector.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iv.
B458880C01
0.375,1.667 0.24,1.313 false 3.063,1.646 3.177,1.302 false 0.323,1.698 0.635,1.896 0.313,0.198 10 false *a 2.969,1.677 3.281,1.875 0.313,0.198 10 false *a
*a Scribed Line


Install the back door outside garnish protector as shown in the illustration.

HINT:

Install each back door outside garnish protector along the line on the No. 2 back door outside garnish.




b.

for TMC Made:

i.

Clean the No. 2 back door outside garnish surface.

1. Using a heat light, heat the No. 2 back door outside garnish surface.

2. Remove the double-sided tape from the No. 2 back door outside garnish.

3. Wipe off any tape adhesive residue with cleaner.



ii.

Using a heat light, heat the No. 2 back door outside garnish.


iii.

Remove the release paper from a new back door outside garnish protector.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iv.
B472762C01
0.521,1.625 0.24,1.292 false 1.458,1.552 1.667,1.156 false 2,1.521 1.802,1.156 false 3,1.625 3.177,1.302 false 0.49,1.635 0.802,1.833 0.313,0.198 10 false *a 1.354,1.563 1.667,1.76 0.313,0.198 10 false *a 2.01,1.552 2.323,1.75 0.313,0.198 10 false *a 2.896,1.656 3.125,1.854 0.229,0.198 10 false *a
*a Scribed Line


Install the back door outside garnish protector as shown in the illustration.

HINT:

Install each back door outside garnish protector along the line on the No. 2 back door outside garnish.




Hide 76825 18.INSTALL BACK DOOR OUTSIDE GARNISH PROTECTOR (for Type B)

HINT:

When installing the back door outside garnish protector, heat the No. 2 back door outside garnish using a heat light.


Heating Temperature:
Item Temperature
No. 2 Back Door Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 2 back door outside garnish excessively.


a.

for TMMT Made:

i.

Clean the No. 2 back door outside garnish surface.

1.

Using a heat light, heat the No. 2 back door outside garnish surface.

2.

Remove the double-sided tape from the No. 2 back door outside garnish.

3.

Wipe off any tape adhesive residue with cleaner.



ii.

Using a heat light, heat the No. 2 back door outside garnish.


iii.

Remove the release paper from a new back door outside garnish protector.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iv.
B557980C01
2.802,1.646 3.01,1.25 false 0.604,1.615 0.406,1.25 false 0.625,1.604 0.938,1.802 0.313,0.198 10 false *a 2.688,1.604 3,1.802 0.313,0.198 10 false *a
*a Scribed Line


Install the back door outside garnish protector as shown in the illustration.

HINT:

Install each back door outside garnish protector along the line on the No. 2 back door outside garnish.




b.

for TMC Made:

i.

Clean the No. 2 back door outside garnish surface.

1.

Using a heat light, heat the No. 2 back door outside garnish surface.

2.

Remove the double-sided tape from the No. 2 back door outside garnish.

3.

Wipe off any tape adhesive residue with cleaner.



ii.

Using a heat light, heat the No. 2 back door outside garnish.


iii.

Remove the release paper from a new back door outside garnish protector.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iv.
B557981C01
0.698,1.604 0.417,1.271 false 1.427,1.5 1.635,1.104 false 1.958,1.469 1.76,1.104 false 2.792,1.625 3.01,1.25 false 0.719,1.594 1.031,1.792 0.313,0.198 10 false *a 1.313,1.51 1.625,1.708 0.313,0.198 10 false *a 1.969,1.469 2.281,1.667 0.313,0.198 10 false *a 2.656,1.604 2.885,1.802 0.229,0.198 10 false *a
*a Scribed Line


Install the back door outside garnish protector as shown in the illustration.

HINT:

Install each back door outside garnish protector along the line on the No. 2 back door outside garnish.




Hide 76822B 19.INSTALL BACK DOOR GARNISH SIDE PROTECTOR LH (for Type A)

HINT:

When installing the back door garnish side protector LH, heat the No. 2 back door outside garnish using a heat light.


Heating Temperature:
Item Temperature
No. 2 Back Door Outside Garnish 20 to 30°C (68 to 86°F)


CAUTION:
·
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the No. 2 Back Door Outside Garnish excessively.


a.

Clean the No. 2 back door outside garnish surface.

i.

Using a heat light, heat the No. 2 back door outside garnish surface.


ii.

Remove the double-sided tape from the No. 2 back door outside garnish.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, No. 2 back door outside garnish.


c.

Remove the release paper from a new back door garnish side protector LH.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B458883C01
0.542,0.271 0.938,0.521 true 0.354,0.104 0.667,0.302 0.313,0.198 10 false *a
*a Scribed Line


Install the back door garnish side protector LH as shown in the illustration.

HINT:

Install each back door garnish side protector LH along the line on the No. 2 back door outside garnish.



Hide 76821B 20.INSTALL BACK DOOR GARNISH SIDE PROTECTOR RH (for Type A)

HINT:

Use the same procedure as for the LH side.


Hide 76812A 21.INSTALL NO. 2 BACK DOOR OUTSIDE GARNISH (for Type A)

a.
B458884C01
0,0 0,0 false
V113147

Install in this Direction


Install the No. 2 back door outside garnish and 7 No. 1 outside moulding retainers as shown in the illustration.


Hide 76812A 22.INSTALL NO. 2 BACK DOOR OUTSIDE GARNISH (for Type B)

a.
B557816C01
0,0 0,0 false
V113147

Install in this Direction


Install the No. 2 back door outside garnish and 7 No. 1 outside moulding retainers as shown in the illustration.