Home › Engine / Hybrid System › M20A-FXS (FUEL) › FUEL TANK › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _083996 M20A-FXS FUEL _0404510 FUEL TANK A

M20A-FXS FUEL  FUEL TANK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Parking Support Brake System*1
Toyota parking assist-sensor system*1
Pre-collision System
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.



PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 2.DRAIN FUEL

Hide 17430 3.REMOVE TAIL EXHAUST PIPE ASSEMBLY

Hide 57628C 4.REMOVE REAR FLOOR SIDE MEMBER COVER LH

a.
A393592N02
0.552,1.813 0.708,2.01 0.156,0.198 10 true A 2,0.156 2.156,0.354 0.156,0.198 10 true B

Remove the 3 bolts and clip (A).


b.

Disengage the clip (B) to remove the rear floor side member cover LH.


Hide 57627A 5.REMOVE REAR FLOOR SIDE MEMBER COVER RH

a.
A393591

Remove the 3 bolts.


b.

Disengage the clip to remove the rear floor side member cover RH.


Hide 77641A 6.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A451705

Remove the 4 clips and No. 1 fuel tank protector from the fuel tank assembly.


Hide 7.DISCONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A451708

Slide the clip and disconnect the charcoal canister outlet hose from the fuel tank filler pipe sub-assembly.


Hide 77213E 8.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A398093

Loosen the clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 9.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A398094

Slide the clip and disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel pipe.


Hide 77209F 10.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A398095

Disconnect the fuel tank main tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>M20A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77100 11.REMOVE FUEL TANK ASSEMBLY

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.
A398092

Disconnect the fuel tank breather tube from the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>M20A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


b.
A374410

Support the fuel tank assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



c.
A398096

Remove the 4 bolts.


d.

Lower the engine lifter to remove the fuel tank assembly.

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




Hide 12.REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A398097

Disengage the 3 clamps to remove the No. 1 fuel evaporation tube sub-assembly from the fuel tank assembly.


Hide 77209F 13.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A398098

Disengage the 3 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.


Hide 14.REMOVE CHARCOAL CANISTER OUTLET HOSE

a.
A432277

Disengage the 2 clamps to remove the charcoal canister outlet hose from the fuel tank assembly.