Home › General › MAINTENANCE › REAR DISC BRAKE PAD (for TMC Made) › 2019.09–2020.08
RM32K0E _V1 General _059911 MAINTENANCE _0407401 REAR DISC BRAKE PAD(for TMC Made) A

MAINTENANCE  REAR DISC BRAKE PAD(for TMC Made)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear disc brake pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>PRECAUTION



Hide 2.PERFORM REAR BRAKE PAD REPLACEMENT MODE

Hide 3.DISABLE BRAKE CONTROL

a.

Wait at least 2 minutes after turning the power switch off.

NOTICE:

When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



b.
C369993C01
0.052,0.052 0.354,0.302 0.302,0.25 12 true *A 0.083,2.313 0.385,2.531 0.302,0.219 12 true *B
*A for LHD
*B for RHD


Disconnect the reservoir level switch connector.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL


d.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


e.

Check that the brake pedal cannot be further depressed.


Hide 4.REMOVE REAR WHEEL

Hide 5.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 04466 6.REMOVE REAR DISC BRAKE PAD

CAUTION:
·
C368019

After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.

·

The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.



a.
C399528

Disconnect the No. 2 parking brake wire assembly from the parking brake actuator assembly.


b.
C422658C01
2.802,2.219 3.115,2.417 0.313,0.198 10 false *a 2.479,0.885 2.792,1.083 0.313,0.198 10 false *b
*a Hold
*b Turn


Hold the rear No. 1 disc brake cylinder slide pin and remove the bolt.


c.
C368445

Pull the rear disc brake cylinder assembly upward.


d.

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 04946 7.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

a.
C418243C01
1.188,0.531 1.521,0.531 false 0.802,0.292 1.135,0.292 false 2.708,1.396 2.802,1.104 2.802,1.104 2.969,1.104 false 0.583,1.688 0.917,1.688 false 1.448,1.948 1.781,1.948 false 1.594,0.438 1.906,0.635 0.313,0.198 10 false *1 1.177,0.198 1.49,0.396 0.313,0.198 10 false *2 3.021,1.021 3.333,1.219 0.313,0.198 10 false *3 1.833,1.865 2.146,2.063 0.313,0.198 10 false *4 0.375,1.594 0.688,1.792 0.313,0.198 10 false *4
*1 Rear No. 1 Disc Brake Anti-squeal Shim
*2 Rear No. 2 Disc Brake Anti-squeal Shim
*3 Rear Disc Brake Anti-squeal Shim
*4 Rear Disc Brake Pad Wear Indicator Plate


Remove the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim from the rear disc brake pad (Inner Side).


b.

Remove the rear disc brake anti-squeal shim from the rear disc brake pad (Outer Side).


c.
C366017

Using a screwdriver, remove the rear disc brake pad wear indicator plate from each rear disc brake pad.