Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE SYSTEM › from 2019.09
RM32K0E _54 Brake _060045 BRAKE SYSTEM (OTHER) _0299578 BRAKE SYSTEM G

BRAKE SYSTEM (OTHER)  BRAKE SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

DTCs may be stored during the inspection procedure. Be sure to clear the DTCs and check that no DTCs are output after the inspection is finished.


PROCEDURE

Hide 1.INSPECT PRESSURE SENSOR

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Set a pedal effort gauge, SST and connect the GTS.

i.
C366601C01
0.635,0.313 0.885,0.313 false 1.823,0.313 2.073,0.313 false 2.521,0.281 2.771,0.281 false 0.292,3.167 0.292,3.24 false 3.073,2.854 3.073,3.042 false 2.115,0.219 2.427,0.375 0.313,0.156 10 false *a 0.948,0.219 1.26,0.375 0.313,0.156 10 false *b 0.219,3.24 0.531,3.396 0.313,0.156 10 false *c 2.99,3.052 3.302,3.208 0.313,0.156 10 false *d 2.313,0.177 2.625,0.333 0.313,0.156 10 false *b
*a Pedal Effort Gauge
*b SST (LSPV Gauge)
*c SST (No. 1 Nipple)
*d SST (No. 3 Nipple)


Set a pedal effort gauge and SST.

SST
09709-29018  (09709-00060, 09709-00080)


ii.

Connect the GTS to the DLC3 with the power switch off, park (P) selected and parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.


iv.

Bleed air from SST (LSPV gauge).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



c.

Inspect the reaction force pressure and servo pressure.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Reaction Force Pressure and Servo Pressure.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Reaction Force Pressure
Servo Pressure
50003 105 500,501

ii.

Check the value output from "Reaction Force Pressure" and "Servo Pressure" by depressing the brake pedal.

Standard Result (for TMC Made):
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Front Right Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0.0 to 0.77 1.4 to 5.4 1.1 to 5.1 MPa (11.2 to 52.0 kgf/cm2, 160 to 740 psi) 1.1 to 5.1 MPa (11.2 to 52.0 kgf/cm2, 160 to 740 psi)
100 N (10 kgf, 22.5 lbf) 0.66 to 1.46 3.9 to 7.9 3.6 to 7.6 MPa (36.7 to 77.5 kgf/cm2, 522 to 1102 psi) 3.6 to 7.6 MPa (36.7 to 77.5 kgf/cm2, 522 to 1102 psi)
150 N (15 kgf, 33.7 lbf) 1.33 to 2.13 6.1 to 10.1 5.8 to 9.8 MPa (59.1 to 99.9 kgf/cm2, 841 to 1421 psi) 5.8 to 9.8 MPa (59.1 to 99.9 kgf/cm2, 841 to 1421 psi)
200 N (20 kgf, 45.0 lbf) 2.02 to 2.82 6.8 to 10.8 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi) 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi)


Standard Result (for TMC Made):
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Front Left Wheel Hydraulic Pressure Rear Right Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0.0 to 0.77 1.4 to 5.4 1.1 to 5.1 MPa (11.2 to 52.0 kgf/cm2, 160 to 740 psi) 1.1 to 5.1 MPa (11.2 to 52.0 kgf/cm2, 160 to 740 psi)
100 N (10 kgf, 22.5 lbf) 0.66 to 1.46 3.9 to 7.9 3.6 to 7.6 MPa (36.7 to 77.5 kgf/cm2, 522 to 1102 psi) 3.6 to 7.6 MPa (36.7 to 77.5 kgf/cm2, 522 to 1102 psi)
150 N (15 kgf, 33.7 lbf) 1.33 to 2.13 6.1 to 10.1 5.8 to 9.8 MPa (59.1 to 99.9 kgf/cm2, 841 to 1421 psi) 5.8 to 9.8 MPa (59.1 to 99.9 kgf/cm2, 841 to 1421 psi)
200 N (20 kgf, 45.0 lbf) 2.02 to 2.82 6.8 to 10.8 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi) 6.5 to 10.5 MPa (66.3 to 107.1 kgf/cm2, 943 to 1523 psi)


Standard Result (for TMMT Made):
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Front Right Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0.08 to 0.88 1.5 to 5.5 1.2 to 5.2 MPa (12.2 to 53.0 kgf/cm2, 174 to 754 psi) 1.2 to 5.2 MPa (12.2 to 53.0 kgf/cm2, 174 to 754 psi)
100 N (10 kgf, 22.5 lbf) 0.74 to 1.54 5.8 to 9.8 5.5 to 9.5 MPa (56.1 to 96.9 kgf/cm2, 798 to 1378 psi) 5.5 to 9.5 MPa (56.1 to 96.9 kgf/cm2, 798 to 1378 psi)
150 N (15 kgf, 33.7 lbf) 1.40 to 2.20 6.9 to 10.9 6.6 to 10.6 MPa (67.3 to 108.1 kgf/cm2, 957 to 1537 psi) 6.6 to 10.6 MPa (67.3 to 108.1 kgf/cm2, 957 to 1537 psi)
200 N (20 kgf, 45.0 lbf) 2.06 to 2.86 6.9 to 10.9 6.6 to 10.6 MPa (67.3 to 108.1 kgf/cm2, 957 to 1537 psi) 6.6 to 10.6 MPa (67.3 to 108.1 kgf/cm2, 957 to 1537 psi)


Standard Result (for TMMT Made):
Pedal Effort Reaction Force Pressure
(MPa)
Servo Pressure
(MPa)
Front Left Wheel Hydraulic Pressure Rear Right Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0.08 to 0.88 1.5 to 5.5 1.2 to 5.2 MPa (12.2 to 53.0 kgf/cm2, 174 to 754 psi) 1.2 to 5.2 MPa (12.2 to 53.0 kgf/cm2, 174 to 754 psi)
100 N (10 kgf, 22.5 lbf) 0.74 to 1.54 5.8 to 9.8 5.5 to 9.5 MPa (56.1 to 96.9 kgf/cm2, 798 to 1378 psi) 5.5 to 9.5 MPa (56.1 to 96.9 kgf/cm2, 798 to 1378 psi)
150 N (15 kgf, 33.7 lbf) 1.40 to 2.20 6.9 to 10.9 6.6 to 10.6 MPa (67.3 to 108.1 kgf/cm2, 957 to 1537 psi) 6.6 to 10.6 MPa (67.3 to 108.1 kgf/cm2, 957 to 1537 psi)
200 N (20 kgf, 45.0 lbf) 2.06 to 2.86 6.9 to 10.9 6.6 to 10.6 MPa (67.3 to 108.1 kgf/cm2, 957 to 1537 psi) 6.6 to 10.6 MPa (67.3 to 108.1 kgf/cm2, 957 to 1537 psi)




d.

Remove the pedal effort gauge and SST.

i.

Remove the pedal effort gauge and SST, and bleed the brake line.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



e.

Inspect the accumulator pressure.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Accumulator Pressure and MT Voltage Value.

Chassis > ABS/VSC/TRC > Data List
Tester Display
MT Voltage Value
Accumulator Pressure
50003 105 279,502

ii.

While fully depressing the brake pedal 4 or 5 times, check that the MT voltage value is 10 V or more once or more.

HINT:

Usually the MT voltage value is 0 V.



iii.

After confirming that the booster pump motor stops, check the accumulator pressure.

Standard Result:

15 to 21 MPa




Hide 47210L 2.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Set a pedal effort gauge, SST and connect the GTS.

i.
C366601C02
1.833,0.292 2.083,0.292 false 2.51,0.292 2.76,0.292 false 0.646,0.292 0.896,0.292 false 0.302,3.177 0.26,3.333 false 3.073,2.854 3.135,3.063 false 2.115,0.208 2.427,0.365 0.313,0.156 10 false *a 2.323,0.208 2.635,0.365 0.313,0.156 10 false *b 0.167,3.344 0.479,3.5 0.313,0.156 10 false *c 3.094,3.094 3.313,3.281 0.219,0.188 10 false *d 0.948,0.208 1.26,0.365 0.313,0.156 10 false *b
*a Pedal Effort Gauge
*b SST (LSPV Gauge)
*c SST (No. 1 Nipple)
*d SST (No. 3 Nipple)


Set a pedal effort gauge and SST.

SST
09709-29018  (09709-00060, 09709-00080)


ii.

Connect the GTS to the DLC3 with the power switch off, park (P) selected and parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.



v.

Bleed air from SST (LSPV gauge).

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING



c.

Check operation without the brake booster.

i.

Inspect and adjust the brake pedal height.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT


ii.
C366947C03
0.885,0.76 1.323,0.99 true 0.927,1.438 1.354,1.271 true 0.677,1.396 0.896,1.615 0.219,0.219 10 true *b 0.625,0.625 0.844,0.844 0.219,0.219 10 true *a
*a Fluid Level Support Line
*b MIN Line


Adjust the brake fluid level in the reservoir between MIN line and fluid level support line.


iii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167

iv.

Select "Motor Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.


v.

Perform "Motor Invalid" according to the display on the GTS.


vi.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.



vii.

Check that the brake pedal is firm.


viii.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor and Stroke Sensor 2.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 105 11,12

ix.

Check the values output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Result (for TMC Made):
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
Front Right Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.09 to 1.79 3.21 to 3.91 0.04 to 2.03 MPa (0.4 to 20.7 kgf/cm2, 6 to 294 psi) 0.04 to 2.03 MPa (0.4 to 20.7 kgf/cm2, 6 to 294 psi)
500 N (51 kgf, 112.4 lbf) 1.24 to 1.94 3.06 to 3.76 2.07 to 4.07 MPa (21.1 to 41.5 kgf/cm2, 300 to 590 psi) 2.07 to 4.07 MPa (21.1 to 41.5 kgf/cm2, 300 to 590 psi)


Standard Result (for TMC Made):
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
Front Left Wheel Hydraulic Pressure Rear Right Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.09 to 1.79 3.21 to 3.91 0.04 to 2.03 MPa (0.4 to 20.7 kgf/cm2, 6 to 294 psi) 0.04 to 2.03 MPa (0.4 to 20.7 kgf/cm2, 6 to 294 psi)
500 N (51 kgf, 112.4 lbf) 1.24 to 1.94 3.06 to 3.76 2.07 to 4.07 MPa (21.1 to 41.5 kgf/cm2, 300 to 590 psi) 2.07 to 4.07 MPa (21.1 to 41.5 kgf/cm2, 300 to 590 psi)


Standard Result (for TMMT Made):
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
Front Right Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.14 to 1.84 3.14 to 3.86 0.03 to 2.03 MPa (0.3 to 20.7 kgf/cm2, 4.4 to 294 psi) 0.03 to 2.03 MPa (0.3 to 20.7 kgf/cm2, 4.4 to 294 psi)
500 N (51 kgf, 112.4 lbf) 1.31 to 2.01 2.99 to 3.69 2.00 to 4.00 MPa (20.4 to 40.8 kgf/cm2, 290 to 580 psi) 2.00 to 4.00 MPa (20.4 to 40.8 kgf/cm2, 290 to 580 psi)


Standard Result (for TMMT Made):
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
Front Left Wheel Hydraulic Pressure Rear Right Wheel Hydraulic Pressure
200 N (20 kgf, 45.0 lbf) 1.14 to 1.84 3.14 to 3.86 0.03 to 2.03 MPa (0.3 to 20.7 kgf/cm2, 4.4 to 294 psi) 0.03 to 2.03 MPa (0.3 to 20.7 kgf/cm2, 4.4 to 294 psi)
500 N (51 kgf, 112.4 lbf) 1.31 to 2.01 2.99 to 3.69 2.00 to 4.00 MPa (20.4 to 40.8 kgf/cm2, 290 to 580 psi) 2.00 to 4.00 MPa (20.4 to 40.8 kgf/cm2, 290 to 580 psi)



x.

Remove the pedal effort gauge and SST, and bleed the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING


xi.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Accumulator Pressure, and check the output pressure.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Accumulator Pressure
50003 105 502
Standard Result:

15 to 21 MPa





Hide 3.INSPECT STROKE SIMULATOR

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Connect the GTS and set a pedal effort gauge.

i.

Set a pedal effort gauge.


ii.

Connect the GTS to the DLC3 with the power switch off, park (P) selected and parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.




c.

Check operation with the brake booster.

i.

Turn the power switch on (IG).


ii.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor and Stroke Sensor 2.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 105 11,12

iii.

Depress the brake pedal 4 or 5 times.


iv.

Check the values output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Voltage (for TMC Made):
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
50 N (5 kgf, 11.2 lbf) 1.03 to 1.73 3.27 to 3.97
100 N (10 kgf, 22.5 lbf) 1.15 to 1.85 3.15 to 3.85
150 N (15 kgf, 33.7 lbf) 1.23 to 1.93 3.07 to 3.77


Standard Voltage (for TMMT Made):
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
50 N (5 kgf, 11.2 lbf) 1.05 to 1.75 3.25 to 3.95
100 N (10 kgf, 22.5 lbf) 1.18 to 1.88 3.12 to 3.82
150 N (15 kgf, 33.7 lbf) 1.28 to 1.98 3.02 to 3.72