Home › Power Source / Network › M20A-FXS (BATTERY / CHARGING) › CHARGING SYSTEM › from 2019.09
RM32K0E _57 Power Source / Network _084047 M20A-FXS BATTERY / CHARGING _0404934 CHARGING SYSTEM C

M20A-FXS BATTERY / CHARGING  CHARGING SYSTEM  P162B87  Lost Communication with Battery Monitor Module Missing Message  


DESCRIPTION

The hybrid vehicle control ECU communicates with the battery state sensor assembly via LIN communication. If a LIN communication error is detected, the hybrid vehicle control ECU stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P162B87 Lost Communication with Battery Monitor Module Missing Message Battery state sensor assembly or hybrid vehicle control ECU communication stops for approximately 17 minutes or more with the power switch on (IG)
(1 trip detection logic)
·

Wire harness or connector

·

Battery state sensor assembly

·

Hybrid vehicle control ECU


Charge warning light does not come on DTC stored SAE Code: P162B

WIRING DIAGRAM

A392148E03
3.927,0.594 4.135,0.844 0.208,0.25 10 false 2 2.313,0.635 2.521,0.885 0.208,0.25 10 false 1 3.917,2.427 4.156,2.635 0.24,0.208 10 false 3 5.448,0.594 5.656,0.844 0.208,0.25 10 false 8 5.719,0.76 6.156,1.01 0.438,0.25 10 false LIN3 5.333,3.417 5.771,3.667 0.438,0.25 10 false A97 5.323,3.594 7.094,3.844 1.771,0.25 10 false Hybrid Vehicle Control ECU 2.125,3.052 2.563,3.302 0.438,0.25 10 false C13 2.135,3.24 4.365,3.448 2.229,0.208 10 false Compressor with Motor Assembly 1.198,4.438 3.073,4.677 1.875,0.24 10 false : LIN Communication Line 0.76,3.438 1.917,3.729 1.156,0.292 10 false Auxiliary Battery 0.635,1.75 1.792,2.042 1.156,0.292 10 false MAIN NO. 2 1.469,0.896 2.125,1.188 0.656,0.292 10 false BATT-S 2.167,1.365 4.396,1.573 2.229,0.208 10 false Battery State Sensor Assembly 2.167,1.188 2.604,1.438 0.438,0.25 10 false M110 2.563,0.74 3,0.99 0.438,0.25 10 false +B 3.552,0.76 3.99,1.01 0.438,0.25 10 false LIN 3.406,2.604 3.844,2.854 0.438,0.25 10 false DOUT

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION
a.

Check installation condition of the battery state sensor assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

INSTALL THE BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



d.
A434715C14
1.458,0.125 1.958,0.375 0.5,0.25 0.844,1.792 1.542,1.167 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 0.573,1.708 1.01,1.927 0.438,0.219 10 false +B 1.531,0.167 2.042,0.365 0.51,0.198 10 false M110
*a Front view of wire harness connector
(to Battery State Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M110-1 (+B) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY STATE SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY STATE SENSOR ASSEMBLY)
a.

Disconnect the A97 hybrid vehicle control ECU connector.


b.

Disconnect the M110 battery state sensor assembly connector.


c.

Disconnect the C13 compressor with motor assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A97-8 (LIN3) - M110-2 (LIN) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A97-8 (LIN3), M110-2 (LIN) or C13-3 (DOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTCS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTCS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check for DTCs, and note down any DTCs that are output.

Click herePower Source / Network>M20A-FXS (BATTERY / CHARGING)>CHARGING SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 397

f.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


g.

Clear the DTCs.

Click herePower Source / Network>M20A-FXS (BATTERY / CHARGING)>CHARGING SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Clear DTCs
50002 397

Result:
Proceed to
NEXT



NEXT

5.CLEAR DTCS (AIR CONDITIONING SYSTEM)
5.CLEAR DTCS (AIR CONDITIONING SYSTEM)
a.

Turn the power switch on (IG).


b.

Turn the GTS on.


c.

Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.


d.

Check for DTCs, and note down any DTCs that are output.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

e.

Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.


f.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCS
6.CHECK FOR DTCS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY) and wait for 17 minutes or more.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check for DTCs.

Click herePower Source / Network>M20A-FXS (BATTERY / CHARGING)>CHARGING SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTC P162B87 is output. A
DTCs are not output. B



A

7.CHECK FOR DTCS (AIR CONDITIONING SYSTEM)

B

7.CHECK FOR DTCS (AIR CONDITIONING SYSTEM)
a.

Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.


b.

Check for DTCs when the following conditions are met.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1498 is output. A
DTCs are not output. B



A

B