Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304571 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P163081  Communication Error from VSC to ECM Invalid Serial Data Received  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) sends signals such as cruise control cancel signals and brake demand response signals to the hybrid vehicle control ECU when the dynamic radar cruise control system is operating.

DTC No. Detection Item DTC Detection Condition Trouble Area
P163081 Communication Error from VSC to ECM Invalid Serial Data Received While the vehicle speed is 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, communication data from the skid control ECU (brake booster with master cylinder assembly) is logically inconsistent for approximately 0.5 seconds or more.
·

CAN communication circuit

·

Skid control ECU (brake booster with master cylinder assembly)

·

Hybrid vehicle control ECU



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CHECK FOR DTCs (CRUISE CONTROL)

B

2.CHECK FOR DTCs (CRUISE CONTROL)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 399

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).

3.

Drive the vehicle at 5 km/h (3 mph) or more for 0.5 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 399

Result:
Result Proceed to
DTC P163081 is not output A
DTC P163081 is output B



A

B

3.REPLACE BRAKE ACTUATOR ASSEMBLY
3.REPLACE BRAKE ACTUATOR ASSEMBLY

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (CRUISE CONTROL)
4.CHECK FOR DTCs (CRUISE CONTROL)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 399

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Turn the power switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF button).

3.

Drive the vehicle at 5 km/h (3 mph) or more for 0.5 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 399

Result:
Result Proceed to
DTC P163081 is not output A
DTC P163081 is output (for 2ZR-FXE) B
DTC P163081 is output (for M20A-FXS) C



A

END

B

C