Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304571 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch is used to turn the dynamic radar cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL.

The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch contains momentary type contacts for each function. The contacts close only while the cruise control main switch is being operated in the direction of the relative function arrow, and open when the cruise control main switch is released. The voltage at the terminal of the hybrid vehicle control ECU assembly changes as each of the different contacts open or close. The hybrid vehicle control ECU assembly reads this voltage and controls the SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL functions accordingly.

·

Vehicle-to-vehicle distance control mode is selected by default when the dynamic radar cruise control system is turned on using the cruise control main switch (ON/OFF button).

·

The operation of constant speed control mode is the same as that for a conventional cruise control system.


WIRING DIAGRAM

for 2ZR-FXE


C367148E04
0.438,1.083 1.115,1.281 0.677,0.198 10 false CANCEL 1.104,1.083 1.563,1.281 0.458,0.198 10 false -SET 1.76,1.083 2.219,1.281 0.458,0.198 10 false +RES 2.396,1.083 3.021,1.281 0.625,0.198 10 false ON/OFF 0.094,1.948 2.563,2.229 2.469,0.281 10 false Cruise Control Main Switch 3.75,0.448 3.896,0.625 0.146,0.177 10 false 3 3.719,0.646 3.896,0.823 0.177,0.177 10 false z4 3.719,1.542 3.896,1.719 0.177,0.177 10 false z4 3.75,1.344 3.896,1.521 0.146,0.177 10 false 4 4.74,0.552 5.094,0.74 0.354,0.188 10 false CCS 4.74,1.458 5.094,1.646 0.354,0.188 10 false ECC 5.26,0.438 5.406,0.615 0.146,0.177 10 false 1 5.188,0.656 5.531,0.833 0.344,0.177 10 false F29 5.188,1.552 5.531,1.729 0.344,0.177 10 false F29 5.271,1.344 5.417,1.521 0.146,0.177 10 false 2 6.135,0.563 6.385,0.74 0.25,0.177 10 false 28 6.385,0.667 6.74,0.854 0.354,0.188 10 false CCS 4.031,1.938 5.135,2.479 1.104,0.542 10 false Spiral Cable Sub-assembly 6.229,1.854 6.573,2.031 0.344,0.177 10 false F2 6.229,2.01 7.156,2.417 0.927,0.406 10 false Hybrid Vehicle Control ECU 3.052,2.073 3.958,2.427 0.906,0.354 10 false Cruise Control Switch Wire 2.99,0.563 3.135,0.74 0.146,0.177 10 false 3 2.99,1.458 3.135,1.635 0.146,0.177 10 false 1


for M20A-FXS


C367148E09
0.438,1.083 1.115,1.281 0.677,0.198 10 false CANCEL 1.104,1.083 1.563,1.281 0.458,0.198 10 false -SET 1.76,1.083 2.219,1.281 0.458,0.198 10 false +RES 2.396,1.083 3.021,1.281 0.625,0.198 10 false ON/OFF 0.094,1.948 2.563,2.229 2.469,0.281 10 false Cruise Control Main Switch 3.75,0.448 3.896,0.625 0.146,0.177 10 false 3 3.719,0.646 3.896,0.823 0.177,0.177 10 false z4 3.719,1.542 3.896,1.719 0.177,0.177 10 false z4 3.75,1.344 3.896,1.521 0.146,0.177 10 false 4 4.74,0.552 5.094,0.74 0.354,0.188 10 false CCS 4.74,1.458 5.094,1.646 0.354,0.188 10 false ECC 5.26,0.438 5.406,0.615 0.146,0.177 10 false 1 5.188,0.656 5.531,0.833 0.344,0.177 10 false F29 5.188,1.552 5.531,1.729 0.344,0.177 10 false F29 5.271,1.344 5.417,1.521 0.146,0.177 10 false 2 6.135,0.563 6.385,0.74 0.25,0.177 10 false 14 6.385,0.667 6.74,0.854 0.354,0.188 10 false CCS 4.031,1.938 5.135,2.479 1.104,0.542 10 false Spiral Cable Sub-assembly 6.229,1.854 6.635,2.031 0.406,0.177 10 false F161 6.229,2.01 7.156,2.417 0.927,0.406 10 false Hybrid Vehicle Control ECU 3.052,2.073 3.958,2.427 0.906,0.354 10 false Cruise Control Switch Wire 2.99,0.563 3.135,0.74 0.146,0.177 10 false 3 2.99,1.458 3.135,1.635 0.146,0.177 10 false 1


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
-SET Switch -SET switch signal ON or OFF ON: -SET switch on
OFF: -SET switch off
-
+RES Switch +RES switch signal ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Cruise Main Switch Operation Condition Cruise control main switch (ON/OFF button) status ON or OFF ON: Cruise control main switch (ON/OFF button) pushed
OFF: Cruise control main switch (ON/OFF button) not pushed
-
Powertrain > Cruise Control > Data List
Tester Display
-SET Switch
+RES Switch
Cruise Main Switch Operation Condition
50003 399 22,23,1
OK:

The Data List items shown in the table change according to the operation of the cruise control main switch.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Remove the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL


b.

Inspect the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE

NG

3.CHECK CRUISE CONTROL SWITCH WIRE
a.
A306566C74
0.333,1.25 0.833,1.5 0.5,0.25 0.438,0.719 0.75,0.917 0.313,0.198 10 false *a 0.51,1.302 0.823,1.5 0.313,0.198 10 false z4 0.5,2.969 0.813,3.167 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Main Switch)


Remove the cruise control switch wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Specified Condition
Cruise control main switch side connector terminal 3 - z4-3 Below 1 Ω
Cruise control main switch side connector terminal 1 - z4-4 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU AND BODY GROUND)
a.

Disconnect the F29 spiral cable sub-assembly connector.


b.

Disconnect the F2 hybrid vehicle control ECU connector. (for 2ZR-FXE)


c.

Disconnect the F161 hybrid vehicle control ECU connector. (for M20A-FXS)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2ZR-FXE:
Tester Connection Condition Specified Condition
F29-1 (CCS) - F2-28 (CCS) Always Below 1 Ω
F29-2 (ECC) - Body ground Always Below 1 Ω
F29-1 (CCS) or F2-28 (CCS) - Body ground Always 10 kΩ or higher

for M20A-FXS:
Tester Connection Condition Specified Condition
F29-1 (CCS) - F161-14 (CCS) Always Below 1 Ω
F29-2 (ECC) - Body ground Always Below 1 Ω
F29-1 (CCS) or F161-14 (CCS) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for 2ZR-FXE) A
OK (for M20A-FXS) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR