Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY › 2019.09–2020.08
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0303874 FRONT PASSENGER AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the instrument panel passenger airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 55401E 2.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 73960A 3.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

CAUTION:
B417757C02
0.917,0.938 1.063,1.125 0.146,0.188 10 false .
V100155

Deployment Side


When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.


a.
B454060

Remove the 2 screws.


b.
B454061

Disengage the hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad sub-assembly.

NOTICE:

Do not damage the deployment surface of the instrument panel passenger airbag assembly.



Hide 82142A 4.REMOVE NO. 2 INSTRUMENT PANEL WIRE

a.
B454066C03
1.698,1.885 2.292,1.677 true 0.802,0.667 1.333,1 true 1.531,1.927 0.917,2.833 true 0.719,2.729 1.031,2.885 0.313,0.156 10 false *a 1.406,0.896 1.719,1.052 0.313,0.156 10 false *c 2.365,1.583 2.677,1.74 0.313,0.156 10 false *b
*a Protective Tape
*b Airbag Connector
*c Airbag Connector Lock


Disengage the clamp.


b.

Using a screwdriver with its tip wrapped in protective tape, release the airbag connector lock.


c.

Disconnect the airbag connector to remove the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.