The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the instrument panel safety pad sub-assembly removal/installation are shown below.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After the power switch off, the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
1. TABLE OF BOLT, SCREW AND NUT
All bolts and screws relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for 2ZR-FXE:
Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL
for M20A-FXS:
Click hereGeneral>MAINTENANCE>M20A-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
4.REMOVE REAR CONSOLE BOX ASSEMBLY
84140
5.REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY
67913
6.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL
62111C
7.REMOVE COWL SIDE TRIM BOARD RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL
55607
8.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the claws and guides to remove the No. 2 instrument panel under cover sub-assembly as shown in the illustration.
55550
9.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
Disengage the claw to disconnect the glove compartment door stopper sub-assembly.
| *a | Stopper Portion |
|
Push |
Disengage the stoppers and pull out the glove compartment door assembly until it is level.
|
Remove in this Direction |
Disengage the hinges to remove the glove compartment door assembly as shown in the illustration.
55054
10.REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
Disengage the claw to remove the glove compartment door stopper sub-assembly.
55433B
11.REMOVE NO. 2 INSTRUMENT PANEL LOWER FINISH PANEL
|
Remove in this Direction |
Remove the 5 screws <D>.
Disengage the clips and claws to remove the No. 2 instrument panel lower finish panel as shown in the illustration.
Disconnect the connector.
62312B
12.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Disconnect the front door opening trim weatherstrip LH from the area shown in the illustration.
62311B
13.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
55436A
14.REMOVE INSTRUMENT PANEL FINISH END PANEL LH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Using a molding remover A, disengage the clips and guides to remove the instrument panel finish end panel LH as shown in the illustration.
55435A
15.REMOVE INSTRUMENT PANEL FINISH END PANEL RH
Use the same procedure as for the LH side.
55318C
16.REMOVE INSTRUMENT SIDE PANEL LH
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Using a molding remover A, disengage the clips and guides to remove the instrument side panel LH as shown in the illustration.
w/ Airbag Cut Off Switch:
Disconnect the connector.
55317A
17.REMOVE INSTRUMENT SIDE PANEL RH
Use the same procedure as for the LH side.
62212
18.REMOVE FRONT PILLAR GARNISH LH
|
Pull up |
Pull up the front pillar garnish LH to disengage the clips as shown in the illustration.
| *a | Release Lever |
|
Push |
Push the release lever and separate the front pillar garnish clips from the vehicle body as shown in the illustration.
If the front pillar garnish clip has significant damage, replace it with a new one.
When the front pillar garnish clip cannot be removed using your fingers:
|
Lift in this Direction |
While pressing the part shown in the illustration with your finger, move the front pillar garnish clip in the direction indicated by the arrow shown in the illustration.
|
Remove in this Direction |
While pulling the front pillar garnish clip in the direction indicated by the arrow, push the part shown in the illustration with the end of a screwdriver and remove the front pillar garnish clip.
If the front pillar garnish clip has significant damage, replace it with a new one.
|
Remove in this Direction |
Disengage the guides to remove the front pillar garnish LH as shown in the illustration.
w/ Speaker:
Disconnect the connector.
Remove the front pillar garnish clip.
| *a | Protective Cover |
|
Adhesive Tape |
Protect the curtain shield airbag assembly.
Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.
Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish LH is removed.
62211
19.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
55408F
20.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the clips, claws and guides to remove the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.
w/ Speaker:
Disconnect the connector.
55409F
21.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Use the same procedure as for the No. 1 instrument panel speaker panel sub-assembly side.
86160P
22.REMOVE NO. 2 FRONT SPEAKER ASSEMBLY (w/ Woofer)
55404D
23.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
|
Remove in this Direction |
Disengage the clips to remove the instrument cluster finish panel sub-assembly as shown in the illustration.
w/ Switch:
Disconnect each connector.
55410C
24.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
|
Remove in this Direction |
Disengage the claws to separate the meter hood spacer as shown in the illustration.
|
Remove in this Direction |
Remove the 2 clips.
Disengage the clips and guides to remove the instrument cluster finish panel assembly as shown in the illustration.
55012A
25.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
|
Remove in this Direction |
Disengage the clips to remove the No. 2 instrument panel garnish sub-assembly as shown in the illustration.
55414C
26.REMOVE STARTER SWITCH BEZEL (for RHD with Entry and Start System)
|
Remove in this Direction |
Disengage the clips to remove the starter switch bezel as shown in the illustration.
Disconnect the connector.
83100
27.REMOVE COMBINATION METER ASSEMBLY
53601
28.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
|
Remove in this Direction |
Disengage the claw and guides to disconnect the hood lock control lever sub-assembly as shown in the illustration.
55545
29.REMOVE FUSE BOX OPENING COVER (w/ Knee Airbag)
|
Remove in this Direction |
Remove the screw <D>.
Disengage the clips to remove the fuse box opening cover as shown in the illustration.
Disconnect each connector.
73997
30.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY WITH DOOR (w/ Knee Airbag)
55545
31.REMOVE FUSE BOX OPENING COVER (w/o Knee Airbag)
|
Remove in this Direction |
Remove the screw <D>.
Disengage the clips and claws to remove the fuse box opening cover with instrument panel lower finish panel sub-assembly as shown in the illustration.
Disconnect each connector.
55045
32.REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)
Remove the 2 screws <D>.
Disengage the clips to remove the instrument panel lower finish panel sub-assembly from the fuse box opening cover.
55405B
33.REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY (w/o Display)
|
Place Hands Here |
|
Remove in this Direction |
Disengage the claws to remove the instrument cluster finish center panel sub-assembly as shown in the illustration.
86120
34.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)
55521C
35.REMOVE STEREO OPENING COVER WITH BRACKET (w/o Radio Receiver)
Remove the 4 bolts <A>.
Disengage the guides to remove the stereo opening cover with bracket.
Disconnect the connector.
86211
36.REMOVE NO. 1 RADIO BRACKET (w/o Radio Receiver)
Remove the 3 screws <D>.
Disengage the guides to remove the No. 1 radio bracket.
86212
37.REMOVE NO. 2 RADIO BRACKET (w/o Radio Receiver)
Remove the 3 screws <D>.
Disengage the guides to remove the No. 2 radio bracket.
55406B
38.REMOVE INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY
|
Remove in this Direction |
Disengage the clips to remove the instrument cluster finish lower center panel sub-assembly as shown in the illustration.
Disconnect the connector.
55414C
39.REMOVE STARTER SWITCH BEZEL (for LHD with Entry and Start System)
|
Remove in this Direction |
Disengage the clips to remove the starter switch bezel as shown in the illustration.
Disconnect the connector.
55011A
40.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (w/o Display)
|
Remove in this Direction |
Disengage the clips and guides to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.
55670A
41.REMOVE INSTRUMENT PANEL CENTER REGISTER ASSEMBLY
|
Remove in this Direction |
Remove the 2 screws <D>.
Disengage the claws and guides to remove the instrument panel center register assembly as shown in the illustration.
86140A
42.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
55011A
43.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (w/ Display)
|
Remove in this Direction |
Remove the 2 bolts <A>.
Disengage the clips and guides to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.
55085
44.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
|
Remove in this Direction |
Disengage the claws to remove the No. 2 heater to register duct sub-assembly as shown in the illustration.
55401E
45.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
for TMMT Made:
| *A | w/o Radio Receiver | - | - |
| *a | Slider | *b | Airbag Bolt |
| *c | Ground Bolt A | *d | Ground Bolt B |
Remove the 4 clips.
w/o Radio Receiver:
Remove the ground bolt B as shown in the illustration.
Remove the 8 bolts and ground bolt A as shown in the illustration.
Slide the slider to disconnect the airbag connector.
except TMMT Made:
| *a | Slider | *b | Airbag Bolt |
| *c | Ground Bolt | - | - |
Remove the 4 clips.
Remove the 9 bolts as shown in the illustration.
Slide the slider to disconnect the airbag connector.
Disconnect each connector.
Disengage each clamp.
Disengage the guides to remove the instrument panel safety pad sub-assembly as shown in the illustration.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |