Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front) › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0304147 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  INSTALLATION  


PROCEDURE

Hide 89347C 1.INSTALL FRONT CENTER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front center ultrasonic sensor retainer is necessary.

·

If a front center ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the front bumper cover.

i.

Remove any remaining double-sided tape from the front bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 30 mm (1.18 in.)


Cover the 2 sensor installation holes with a 30 mm (1.18 in.) circular piece of tape.


c.
E426327C01
0.656,1.104 0.99,1.104 true 0.427,1.021 0.646,1.219 0.219,0.198 10 true *a
*a Scribed Line
V100144

Primer Application


Apply primer to front bumper assembly on the installation area of the front center ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front center ultrasonic sensor retainer has been attached.




d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new front center ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.
E426328C01
0.635,1.063 0.969,1.063 true 2.552,1.698 2.906,1.375 2.906,1.375 2.406,1.458 true 0.417,0.969 0.646,1.167 0.229,0.198 10 true *a 2.938,1.219 3.167,1.417 0.229,0.198 10 true *b
*a Scribed Line
*b Identification Code
V100155

Press area


Check that the identification codes on the front bumper assembly and the front center ultrasonic sensor retainer are identical.


h.

Align the front center ultrasonic sensor retainer with the scribed line on the front bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the front center ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the front bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 89347B 2.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

If a front corner ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the front bumper cover.

i.

Remove any remaining double-sided tape from the front bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 30 mm (1.18 in.)


Cover the 2 sensor installation holes with a 30 mm (1.18 in.) circular piece of tape.


c.
E426325C01
0.625,1.115 0.958,1.115 true 0.417,1.021 0.635,1.219 0.219,0.198 10 true *a
*a Scribed Line
V100144

Primer Application


Apply primer to front bumper assembly on the installation area of the front corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front corner ultrasonic sensor retainer has been attached.




d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new front corner ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.
E426326C01
0.563,1.177 0.896,1.177 true 1.198,0.833 1.167,0.417 1.167,0.417 1.583,0.5 true 0.365,1.083 0.594,1.281 0.229,0.198 10 true *a 1.021,0.167 1.25,0.365 0.229,0.198 10 true *b
*a Scribed Line
*b Identification Code
V100155

Press area


Check that the identification codes on the front bumper assembly and the front corner ultrasonic sensor retainer are identical.


h.

Align the front corner ultrasonic sensor retainer with the scribed line on the front bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the front corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the front bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 52128B 3.INSTALL FRONT BUMPER HOLE COVER LH

HINT:

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REASSEMBLY


Hide 52127D 4.INSTALL FRONT BUMPER HOLE COVER RH

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

The following procedure is for the LH side.



Hide 89347D 5.INSTALL FRONT SIDE ULTRASONIC SENSOR RETAINER (w/ Simple Intelligent Parking Assist System)

HINT:
·

Perform this procedure only when replacement of the front side ultrasonic sensor retainer is necessary.

·

If a front side ultrasonic sensor retainer has been removed, replace it with a new one.



a.

Clean the surface of the front bumper cover.

i.

Remove any remaining double-sided tape from the front bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 30 mm (1.18 in.)


Cover the 2 sensor installation holes with a 30 mm (1.18 in.) circular piece of tape.


c.

Apply primer to front bumper assembly on the installation area of the front side ultrasonic sensor retainer using a brush or felt.

E426323C01
0.417,0 3.167,1.75 2.75,1.75 3.917,0 6.75,1.75 2.833,1.75 4.667,0.833 5,0.833 true 2.167,0.833 2.5,0.833 true 0.458,0.052 0.719,0.271 0.26,0.219 12 true *A 4.042,0.031 4.302,0.25 0.26,0.219 12 true *B 2.5,0.729 2.75,0.938 0.25,0.208 10 true *a 4.427,0.75 4.677,0.958 0.25,0.208 10 true *a
*A for LH Side *B for RH Side
*a Scribed Line - -
V100144

- -


NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front side ultrasonic sensor retainer has been attached.




d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new front side ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.

Check that the identification codes on the front bumper assembly and the front side ultrasonic sensor retainer are identical.

E426324C01
0.417,0 3.167,1.75 2.75,1.75 3.917,0 6.75,1.75 2.833,1.75 2.188,0.74 2.521,0.74 true 4.635,0.833 4.969,0.833 true 1.333,0.667 0.833,0.667 0.833,0.667 1.115,0.479 true 5.688,0.667 6.177,0.677 6.177,0.677 5.917,0.417 true 4.354,0.729 4.625,0.958 0.271,0.229 10 true *a 0.5,0.083 0.781,0.313 0.281,0.229 12 true *A 4,0.063 4.281,0.292 0.281,0.229 12 true *B 2.531,0.646 2.802,0.875 0.271,0.229 10 true *a 6.208,0.573 6.479,0.802 0.271,0.229 10 true *b 0.542,0.583 0.813,0.813 0.271,0.229 10 true *b
*A for LH Side *B for RH Side
*a Scribed Line *b Identification Code
V100155

Press area - -



h.

Align the front side ultrasonic sensor retainer with the scribed line on the front bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the front side ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the front bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 89341L 6.INSTALL FRONT CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E426321

Engage the claws to install the front center ultrasonic sensor.


b.

Connect the connector.


Hide 89341K 7.INSTALL FRONT CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E426318

Engage the claws to install the front corner ultrasonic sensor.


b.

Connect the connector.


Hide 89341M 8.INSTALL FRONT SIDE ULTRASONIC SENSOR (w/ Simple Intelligent Parking Assist System)

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E427177

Engage the claws to install the front side ultrasonic sensor.


b.

Connect the connector.


Hide 9.INSTALL FRONT BUMPER ASSEMBLY