Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear) › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0304148 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  INSTALLATION  


PROCEDURE

Hide 89348S 1.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

If a rear center ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the rear bumper cover.

i.

Remove any remaining double-sided tape from the rear bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 30 mm (1.18 in.)


Cover the 2 sensor installation holes with a 30 mm (1.18 in.) circular piece of tape.


c.
E426500C02
0.583,1.094 0.917,1.083 true 0.323,1 0.542,1.198 0.219,0.198 10 true *a
*a Scribed Line
V100144

Primer Application


Apply primer to rear bumper assembly on the installation area of the rear center ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear center ultrasonic sensor retainer has been attached.




d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new rear center ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.
E426501C02
2.969,1.135 2.656,1.135 true 1,1.75 0.688,1.542 0.688,1.542 1.021,1.104 true 2.979,1.042 3.229,1.302 0.25,0.26 10 true *a 0.438,1.469 0.667,1.667 0.229,0.198 10 true *b
*a Scribed Line
*b Identification Code
V100155

Press area


Check that the identification codes on the rear bumper assembly and the rear center ultrasonic sensor retainer are identical.


h.

Align the rear center ultrasonic sensor retainer with the scribed line on the rear bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the rear center ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the rear bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 89348R 2.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

If a rear corner ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the rear bumper cover.

i.

Remove any remaining double-sided tape from the rear bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 30 mm (1.18 in.)


Cover the 2 sensor installation holes with a 30 mm (1.18 in.) circular piece of tape.


c.
E426498C02
0.938,1.146 1.271,1.135 true 0.688,1.063 0.906,1.26 0.219,0.198 10 true *a
*a Scribed Line
V100144

Primer Application


Apply primer to rear bumper assembly on the installation area of the rear corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear corner ultrasonic sensor retainer has been attached.




d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new rear corner ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.
E426499C02
1.323,1.229 1.01,1.229 true 1.406,0.688 1.083,0.25 1.083,0.25 1.5,0.25 true 0.74,1.146 0.99,1.406 0.25,0.26 10 true *a 0.854,0.146 1.083,0.344 0.229,0.198 10 true *b
*a Scribed Line
*b Identification Code
V100155

Press area


Check that the identification codes on the rear bumper assembly and the rear corner ultrasonic sensor retainer are identical.


h.

Align the rear corner ultrasonic sensor retainer with the scribed line on the rear bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the rear corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the rear bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 52164A 3.INSTALL REAR BUMPER PLATE LH

HINT:

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER>DISASSEMBLY


Hide 52163A 4.INSTALL REAR BUMPER PLATE RH

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

The following procedure is for the LH side.



Hide 89348T 5.INSTALL REAR SIDE ULTRASONIC SENSOR RETAINER (w/ Simple Intelligent Parking Assist System)

HINT:
·

Perform this procedure only when replacement of the rear side ultrasonic sensor retainer is necessary.

·

If a rear side ultrasonic sensor retainer has been removed, replace it with a new one.



a.

Clean the surface of the rear bumper cover.

i.

Remove any remaining double-sided tape from the rear bumper cover.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 30 mm (1.18 in.)


Cover the 2 sensor installation holes with a 30 mm (1.18 in.) circular piece of tape.


c.

Apply primer to rear bumper assembly on the installation area of the rear side ultrasonic sensor retainer using a brush or felt.

E426496C02
0.417,0 3.25,1.781 2.833,1.781 3.917,0 6.75,1.781 2.833,1.781 2.052,1 2.385,1 true 4.729,1 5.063,1 true 2.396,0.917 2.594,1.115 0.198,0.198 10 true *a 4.531,0.896 4.729,1.094 0.198,0.198 10 true *a 0.458,0.031 0.698,0.229 0.24,0.198 12 true *A 3.958,0.021 4.198,0.219 0.24,0.198 12 true *B
*A for LH Side *B for RH Side
*a Scribed Line - -
V100144

Primer Application - -


NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear side ultrasonic sensor retainer has been attached.




d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new rear side ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.

Check that the identification codes on the rear bumper assembly and the rear side ultrasonic sensor retainer are identical.

E426497C02
0.417,0 3.25,1.75 2.833,1.75 3.958,0 6.792,1.75 2.833,1.75 1.073,0.823 1.406,0.823 true 5.656,0.771 5.99,0.771 true 2.448,0.333 2.865,0.333 2.865,0.333 2.167,0.646 true 4.729,0.448 4.313,0.448 4.313,0.448 4.917,0.667 true 0.885,0.729 1.073,0.917 0.188,0.188 10 true *a 6.021,0.667 6.208,0.854 0.188,0.188 10 true *a 2.865,0.229 3.052,0.417 0.188,0.188 10 true *b 4.135,0.365 4.323,0.552 0.188,0.188 10 true *b 0.458,0.031 0.729,0.219 0.271,0.188 12 true *A 3.979,0.042 4.25,0.229 0.271,0.188 12 true *B
*A for LH Side *B for RH Side
*a Scribed Line *b Identification Code
V100155

Press area - -



h.

Align the rear side ultrasonic sensor retainer with the scribed line on the rear bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the rear side ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the rear bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 89342A 6.INSTALL REAR CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E426494

Engage the claws to install the rear center ultrasonic sensor.


b.

Connect the connector.


Hide 89342 7.INSTALL REAR CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E426491

Engage the claws to install the rear corner ultrasonic sensor.


b.

Connect the connector.


Hide 89342B 8.INSTALL REAR SIDE ULTRASONIC SENSOR (w/ Simple Intelligent Parking Assist System)

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E427178

Engage the claws to install the rear side ultrasonic sensor.


b.

Connect the connector.


Hide 9.INSTALL REAR BUMPER ASSEMBLY