Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for RHD) › 2019.09–2020.08
RM32K0E _54 Brake _060045 BRAKE SYSTEM (OTHER) _0299586 BRAKE BOOSTER PUMP(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for RHD)  INSTALLATION  


PROCEDURE

Hide 47070 1.INSTALL BRAKE BOOSTER PUMP ASSEMBLY

a.
C343283C01
2.375,0.448 2.552,0.448 true 1.74,0.719 2.146,0.719 true 2.896,2.917 2.656,2.917 false 1.135,4.031 1.135,3.865 1.135,3.865 0.927,3.865 false 2.469,4.167 2.229,4.167 false 1.052,4.365 1.052,4.49 1.052,4.49 0.844,4.49 false 2.594,0.385 2.906,0.542 0.313,0.156 10 false *1 1.563,0.656 1.875,0.813 0.313,0.156 10 false *2 2.51,4.094 2.823,4.25 0.313,0.156 10 false *a 2.938,2.854 3.25,3.01 0.313,0.156 10 false *b 0.76,3.802 1.073,3.958 0.313,0.156 10 false *c 0.677,4.427 0.99,4.583 0.313,0.156 10 false *d
*1 Brake Booster Pump Collar
*2 Brake Booster Pump Bushing
*a Union
*b Connector
*c Wire Harness
*d Stud


Install the brake booster pump assembly, brake booster pump bushing and brake actuator case collar to the brake actuator bracket assembly.

NOTICE:
·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.

·

When installing the brake booster pump assembly to the brake actuator bracket assembly, confirm that the 2 brake booster pump bushings and 2 brake booster pump collars are on the brake booster pump assembly.

·

If installing a new brake booster pump assembly, do not remove the hole plugs before connecting the brake lines because the brake booster pump assembly is filled with brake fluid.

·

Do not carry the brake booster pump assembly by the parts shown in the illustration.




b.

Install the nut.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


c.
C343280N01
2.188,1.5 2.292,1.646 0.104,0.146 10 true 1 1.51,1.51 1.615,1.656 0.104,0.146 10 true 2 1.083,1.094 1.188,1.24 0.104,0.146 10 true 3 1.073,0.583 1.177,0.729 0.104,0.146 10 true 4 0.802,0.271 0.906,0.417 0.104,0.146 10 true 5

Engage the claw and 4 clamps to install the brake booster pump assembly wire harness to the brake actuator assembly bracket.

NOTICE:

Engage the clamps and claw in the order shown in the illustration.



Hide 47381 2.INSTALL NO. 1 BRAKE TUBE CLAMP BRACKET

a.

Install the No. 1 brake tube clamp bracket to the brake booster pump assembly with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 44571A 3.INSTALL NO. 1 BRAKE ACTUATOR HOSE

a.
C343279C01
1.01,2.229 1.24,2.229 1.24,2.229 1.24,2.427 true 1.708,3.094 1.708,2.885 true 2.073,2.156 1.875,2.156 1.875,2.156 1.708,2.594 true 1.135,3.073 1.375,3.073 1.375,3.073 1.479,2.792 true 1.646,3.115 1.823,3.25 0.177,0.135 10 true *1 0.833,2.156 1.01,2.302 0.177,0.146 10 true *a 2.094,2.104 2.271,2.24 0.177,0.135 10 true *b 0.948,3.01 1.125,3.146 0.177,0.135 10 true *c
*1 Brake Actuator Hose Clamp
*a Protector
*b Identification Mark
*c Contacts


Install the No. 1 brake actuator hose to the brake actuator hose clamp.

NOTICE:
·

Make sure to install the No. 1 brake actuator hose so that the protector on the brake booster pump assembly side contacts the brake actuator hose clamp.

·

Make sure to install the No. 1 brake actuator hose so that its identification mark can be seen.




b.
C347173C02
0.479,1.833 0.479,1.594 true 0.646,1.531 0.646,1.24 0.646,1.24 0.896,1.24 true 0.927,1.167 1.146,1.313 0.219,0.146 10 true *a 0.417,1.844 0.615,1.99 0.198,0.146 10 true *b 1.75,2.344 2.042,2.531 0.292,0.188 10 false 90° 1.75,2.99 2.042,3.177 0.292,0.188 10 false 90°
*a Identification Mark
*b Rib of Brake Booster Pump Assembly Port
V100136

Front of the vehicle


Install the No. 1 brake actuator hose to the brake booster pump assembly, and slide the clip to secure it.

NOTICE:
·

When installing the No. 1 brake actuator hose, make sure to align its alignment mark with the rib of the brake booster pump assembly.

·

Install the clip within the range shown in the illustration.




Hide 4.INSTALL BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY

a.
C366966N01
2.563,1.333 2.719,1.531 0.156,0.198 10 true 1 2.948,1.354 3.104,1.552 0.156,0.198 10 true 2 1.938,3.229 2.094,3.427 0.156,0.198 10 true 3 1.396,3.219 1.552,3.417 0.156,0.198 10 true 4

Install the brake actuator with brake booster pump assembly to the vehicle body with the 2 bolts and 2 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Tighten the bolts and nuts in the order shown in the illustration.

·

Do not apply excessive force to the brake lines.

·

Do not hold the brake booster pump assembly by the connector, union or wire harness.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with brake booster pump assembly when carrying it.



HINT:

Install the brake actuator with brake booster pump assembly while avoiding the brake lines.



b.

Engage the clamp to install a new No. 4 brake tube clamp to the brake actuator bracket assembly.


c.

Engage the 2 clamps to install the 2 brake lines to the No. 4 brake tube clamp.


d.
C366964C01
1.333,1.552 1.531,1.302 true 2.385,1.51 2.073,1.073 true 2.219,0.698 1.906,0.802 true 2.01,0.448 1.729,0.854 true 0.958,0.469 1.479,0.927 true 0.969,0.875 1.281,1.021 true 1.188,1.604 1.427,1.813 0.24,0.208 10 true *a 2.396,1.552 2.635,1.75 0.24,0.198 10 true *b 2.24,0.604 2.5,0.813 0.26,0.208 10 true *c 2.052,0.302 2.271,0.5 0.219,0.198 10 true *d 0.74,0.344 0.927,0.542 0.188,0.198 10 true *e 0.698,0.76 0.927,0.99 0.229,0.229 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.


e.
C366967C01
2.677,2.573 2.677,2.802 2.677,2.802 2.823,2.802 false 1.76,2.844 2.073,3 0.313,0.156 10 false *a 2.875,2.708 3.188,2.865 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the 6 brake lines.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




f.
C366968C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.




g.

Engage the clamp to install the wire harness.


h.
C343269C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake booster pump assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.




Hide 473A1 5.INSTALL ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.

Temporarily tighten the accumulator to brake master cylinder tube to the brake booster pump assembly.


b.

Install the accumulator to brake master cylinder tube with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


c.
C367992C01
1.76,2.823 2.073,2.979 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, tighten the accumulator to brake master cylinder tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the accumulator to brake master cylinder tube.

·

Do not allow the accumulator to brake master cylinder tube to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 44571A 6.INSTALL NO. 1 BRAKE ACTUATOR HOSE

a.
C367993C01
1.833,1.156 1.969,1.438 true 1.948,1.458 2.146,1.667 0.198,0.208 10 true *a 1.677,2.958 2.135,3.156 0.458,0.198 10 false 90° 1.698,2.292 2.156,2.49 0.458,0.198 10 false 90°
*a Identification Mark
V100136

Front of the vehicle


Connect the No. 1 brake actuator hose to the No. 1 brake actuator tube to install it, and slide the clip to secure it.

NOTICE:
·

Make sure to connect the No. 1 brake actuator hose with its identification mark facing the front of the vehicle.

·

Install the clip within the range shown in the illustration.




Hide 44551C 7.BLEED NO. 1 BRAKE ACTUATOR TUBE

Hide 8.FILL RESERVOIR WITH BRAKE FLUID

Hide 9.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (for 2ZR-FXE)

Hide 10.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE (for M20A-FXS)

Hide 86510A 11.INSTALL SECURITY HORN ASSEMBLY (w/ Security Horn)

Hide 12.BLEED BRAKE SYSTEM