Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1653  Driver Side Seat Position Sensor  


DESCRIPTION

The seat position airbag sensor circuit consists of the airbag sensor assembly and seat position airbag sensor.

DTC B1653 is stored when a malfunction is detected in the seat position airbag sensor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1653 Driver Side Seat Position Sensor
·

The airbag sensor assembly detects a line short in the seat position airbag sensor circuit.

·

The airbag sensor assembly detects a short to ground in the seat position airbag sensor circuit.

·

The airbag sensor assembly detects a short to B+ in the seat position airbag sensor circuit.

·

The airbag sensor assembly detects an open in the seat position airbag sensor circuit.

·

Seat position airbag sensor malfunction

·

Airbag sensor assembly malfunction


for LHD:
·

Floor wire

·

Front seat wire LH

·

Seat position airbag sensor

·

Airbag sensor assembly


for RHD:
·

Floor wire

·

Front seat wire RH

·

Seat position airbag sensor

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Power switch on (IG) ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the seat position airbag sensor circuit ○ - - - - -
The airbag sensor assembly detects a short to ground in the seat position airbag sensor circuit - ○ - - - -
The airbag sensor assembly detects a short to B+ in the seat position airbag sensor circuit - - ○ - - -
The airbag sensor assembly detects an open in the seat position airbag sensor circuit - - - ○ - -
Seat position airbag sensor malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

for LHD:
B518207E05
5.333,1.073 5.833,1.417 0.5,0.344 10 false LSP+ 5.333,1.99 5.833,2.333 0.5,0.344 10 false LSP- 5.094,1.073 5.417,1.406 0.323,0.333 10 false 25 5.083,1.99 5.396,2.375 0.313,0.385 10 false 26 3.323,1.177 3.74,1.458 0.417,0.281 10 false MZ2 1.719,1.083 2.135,1.365 0.417,0.281 10 false 2 0.406,2.521 0.896,2.688 0.49,0.167 10 false Z4 0.396,2.677 2.229,3.198 1.833,0.521 10 false Seat Position Airbag Sensor 1.719,1.99 2.135,2.271 0.417,0.281 10 false 1 5.281,2.917 6.76,3.094 1.479,0.177 10 false M102 5.281,3.083 6.938,3.531 1.656,0.448 10 false Airbag Sensor Assembly 3.323,2.094 3.74,2.375 0.417,0.281 10 false MZ2 3.438,0.99 3.854,1.271 0.417,0.281 10 false 2 3.438,1.906 3.854,2.188 0.417,0.281 10 false 1 1.25,1.073 1.667,1.417 0.417,0.344 10 false LSP+ 1.25,1.99 1.667,2.333 0.417,0.344 10 false LSP-

for RHD:
B518207E06
5.333,1.073 5.854,1.406 0.521,0.333 10 false RSP+ 5.333,1.99 5.792,2.302 0.458,0.313 10 false RSP- 5.094,1.073 5.417,1.406 0.323,0.333 10 false 32 5.083,1.99 5.396,2.375 0.313,0.385 10 false 31 3.323,1.177 3.74,1.458 0.417,0.281 10 false MY2 1.719,1.083 2.135,1.365 0.417,0.281 10 false 2 0.406,2.521 0.948,2.708 0.542,0.188 10 false Y3 0.396,2.677 2.229,3.198 1.833,0.521 10 false Seat Position Airbag Sensor 1.385,1.083 1.625,1.49 0.24,0.406 10 false VS 1.302,1.99 1.646,2.281 0.344,0.292 10 false GND 1.719,1.99 2.135,2.271 0.417,0.281 10 false 1 5.281,2.917 6.781,3.104 1.5,0.188 10 false M103 5.281,3.083 6.938,3.531 1.656,0.448 10 false Airbag Sensor Assembly 3.323,2.094 3.74,2.375 0.417,0.281 10 false MY2 3.438,0.99 3.854,1.271 0.417,0.281 10 false 2 3.438,1.906 3.854,2.188 0.417,0.281 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK CONNECTION OF CONNECTORS

B

8.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and seat position airbag sensor. Also check that the connectors that link the floor wire and front seat wire LH are properly connected.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and seat position airbag sensor. Also disconnect the connectors that link the floor wire and front seat wire LH.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS

NG

REPLACE FLOOR WIRE OR FRONT SEAT WIRE LH

4.CHECK WIRE HARNESS
a.
B518211C03
0.615,0.51 1.052,0.771 0.438,0.26 0.406,3.604 0.76,3.823 0.354,0.219 1.052,1.208 1.49,1.552 true 2.646,1.208 1.635,1.563 true 1,1.979 1.417,1.979 false 1.875,3.021 1.875,2.792 false 1.156,2.74 1.156,2.406 1.156,2.406 0.99,2.406 false 0.854,4.229 1.219,3.833 true 1.729,4.219 1.375,3.833 true 0.219,2.677 0.656,2.958 0.438,0.281 10 false *1 2.802,2.979 3.24,3.26 0.438,0.281 10 false *2 2.5,2.688 2.938,2.969 0.438,0.281 10 false A 2.146,2.688 2.583,2.969 0.438,0.281 10 false B 1.552,2.688 1.99,2.969 0.438,0.281 10 false C 1.396,2.688 1.833,2.969 0.438,0.281 10 false D 0.802,2.688 1.24,2.969 0.438,0.281 10 false E 0.458,2.688 0.896,2.969 0.438,0.281 10 false F 0.667,0.552 1.063,0.833 0.396,0.281 10 false M102 0.521,0.219 0.958,0.5 0.438,0.281 10 false *a 0.646,1.115 1.052,1.448 0.406,0.333 10 false LSP+ 1.802,3.031 2.24,3.313 0.438,0.281 10 false *4 0.844,1.906 1.281,2.188 0.438,0.281 10 false *5 0.25,3.344 0.688,3.625 0.438,0.281 10 false *b 0.5,3.625 0.729,3.865 0.229,0.24 10 false Z4 0.698,4.25 1.229,4.542 0.531,0.292 10 false LSP- 0.844,2.333 1.281,2.615 0.438,0.281 10 false *3 2.698,1.104 3.229,1.438 0.531,0.333 10 false LSP- 1.604,4.24 2.104,4.521 0.5,0.281 10 false LSP+
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Front Seat Wire LH
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the connectors that link the floor wire and front seat wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z4-2 (LSP+) - Body ground Power switch on (IG) Below 1 V
Z4-1 (LSP-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 25 (LSP+) and 26 (LSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z4-2 (LSP+) - Z4-1 (LSP-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z4-2 (LSP+) - Z4-1 (LSP-) Always 1 MΩ or higher
Z4-2 (LSP+) - Body ground Always 1 MΩ or higher
Z4-1 (LSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

7.CHECK FLOOR WIRE
5.CHECK DTC
a.
B521680C01
0.385,0.771 0.823,1.229 0.438,0.458 10 false *1 2.635,1.052 3.094,1.833 0.458,0.781 10 false *2 2.323,0.781 2.781,1.563 0.458,0.781 10 false A 2.167,0.781 2.625,1.563 0.458,0.781 10 false B 1.552,0.781 2.01,1.563 0.458,0.781 10 false C 1.396,0.781 1.854,1.563 0.458,0.781 10 false D 0.781,0.781 1.24,1.563 0.458,0.781 10 false E 0.625,0.781 1.083,1.563 0.458,0.781 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and seat position airbag sensor.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653 is not output.


HINT:

Codes other than DTC B1653 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG

6.CHECK SEAT POSITION AIRBAG SENSOR
6.CHECK SEAT POSITION AIRBAG SENSOR
a.
B521680C01
0.385,0.771 0.823,1.229 0.438,0.458 10 false *1 2.635,1.052 3.094,1.833 0.458,0.781 10 false *2 2.323,0.781 2.781,1.563 0.458,0.781 10 false A 2.167,0.781 2.625,1.563 0.458,0.781 10 false B 1.552,0.781 2.01,1.563 0.458,0.781 10 false C 1.396,0.781 1.854,1.563 0.458,0.781 10 false D 0.781,0.781 1.24,1.563 0.458,0.781 10 false E 0.625,0.781 1.083,1.563 0.458,0.781 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Replace the seat position airbag sensor with a known good one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the power switch off.


h.

Turn the power switch on (IG), and wait for at least 60 seconds.


i.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653 is not output.


HINT:

Codes other than DTC B1653 may be output at this time, but they are not related to this check.



j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



l.

Restore the seat position airbag sensor that was installed for testing to its original location.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

NG

7.CHECK FLOOR WIRE
a.
B521682C02
0.771,0.521 1.198,0.792 0.427,0.271 0.438,3.635 0.792,3.885 0.354,0.25 0.833,4.24 1.115,3.875 true 1.646,4.24 1.406,3.875 true 1.188,2 1.521,2 false 1.25,1.25 1.604,1.583 true 2.74,1.25 1.75,1.583 true 0.885,2.417 1.052,2.417 1.052,2.417 1.052,2.75 false 1.823,2.417 1.99,2.417 1.99,2.417 1.99,2.75 false 0.813,0.573 1.198,0.865 0.385,0.292 10 false M102 0.75,0.208 1.292,0.604 0.542,0.396 10 false *a 0.375,3.344 0.917,3.74 0.542,0.396 10 false *b 0.156,2.677 0.573,3.031 0.417,0.354 10 false *1 0.729,2.333 1.146,2.688 0.417,0.354 10 false *3 2.875,2.958 3.292,3.313 0.417,0.354 10 false *2 2.563,2.698 2.979,3.052 0.417,0.354 10 false A 2.26,2.688 2.677,3.042 0.417,0.354 10 false B 1.615,2.688 2.031,3.042 0.417,0.354 10 false C 1.323,2.688 1.74,3.042 0.417,0.354 10 false D 0.688,2.677 1.104,3.031 0.417,0.354 10 false E 0.396,2.677 0.813,3.031 0.417,0.354 10 false F 0.469,3.677 0.813,3.917 0.344,0.24 10 false MZ2 1.531,4.25 2.219,4.583 0.688,0.333 10 false LSP+ 0.708,4.25 1.208,4.667 0.5,0.417 10 false LSP- 0.875,1.167 1.365,1.719 0.49,0.552 10 false LSP+ 2.781,1.167 3.365,1.75 0.583,0.583 10 false LSP- 1.031,1.917 1.573,2.313 0.542,0.396 10 false *5 1.667,2.333 2.083,2.688 0.417,0.354 10 false *4
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Front Seat Wire LH
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Wire LH)


Disconnect the floor wire connector from the front seat wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
MZ2-2 (LSP+) - Body ground Power switch on (IG) Below 1 V
MZ2-1 (LSP-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 25 (LSP+) and 26 (LSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MZ2-2 (LSP+) - MZ2-1 (LSP-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MZ2-2 (LSP+) - MZ2-1 (LSP-) Always 1 MΩ or higher
MZ2-2 (LSP+) - Body ground Always 1 MΩ or higher
MZ2-1 (LSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE LH

NG

REPLACE FLOOR WIRE

8.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and seat position airbag sensor. Also check that the connectors that link the floor wire and front seat wire RH are properly connected.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

9.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

9.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and seat position airbag sensor. Also disconnect the connectors that link the floor wire and front seat wire RH.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

10.CHECK WIRE HARNESS

NG

REPLACE FLOOR WIRE OR FRONT SEAT WIRE RH

10.CHECK WIRE HARNESS
a.
B521686C02
0.615,0.51 1.052,0.771 0.438,0.26 0.271,3.719 0.625,3.948 0.354,0.229 1.156,1.208 2.177,1.51 true 2.688,1.208 2.333,1.5 true 2.406,1.938 2.823,1.938 false 0.771,4.323 1.052,3.927 true 1.51,4.323 1.24,3.938 true 1.156,2.969 1.156,2.635 1.156,2.635 0.99,2.635 false 1.885,2.969 1.885,2.635 1.885,2.635 1.719,2.635 false 0.219,2.906 0.656,3.188 0.438,0.281 10 false *1 2.802,2.635 3.24,2.917 0.438,0.281 10 false *2 2.5,2.917 2.938,3.198 0.438,0.281 10 false A 2.146,2.917 2.583,3.198 0.438,0.281 10 false B 1.552,2.917 1.99,3.198 0.438,0.281 10 false C 1.396,2.917 1.833,3.198 0.438,0.281 10 false D 0.802,2.917 1.24,3.198 0.438,0.281 10 false E 0.458,2.906 0.896,3.188 0.438,0.281 10 false F 0.667,0.563 1.104,0.844 0.438,0.281 10 false M103 0.521,0.219 0.958,0.5 0.438,0.281 10 false *a 0.76,1.125 1.292,1.458 0.531,0.333 10 false RSP- 1.563,2.563 2,2.844 0.438,0.281 10 false *4 2.854,1.854 3.292,2.135 0.438,0.281 10 false *5 0.25,3.438 0.688,3.719 0.438,0.281 10 false *b 1.448,4.323 1.854,4.531 0.406,0.208 10 false VS 0.344,3.75 0.615,4 0.271,0.25 10 false Y3 2.729,1.125 3.26,1.458 0.531,0.333 10 false RSP+ 0.844,2.552 1.281,2.833 0.438,0.281 10 false *3 0.625,4.323 1.146,4.531 0.521,0.208 10 false GND
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Front Seat Wire RH
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the connectors that link the floor wire and front seat wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Y3-2 (VS) - Body ground Power switch on (IG) Below 1 V
Y3-1 (GND) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 32 (RSP+) and 31 (RSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y3-2 (VS) - Y3-1 (GND) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y3-2 (VS) - Y3-1 (GND) Always 1 MΩ or higher
Y3-2 (VS) - Body ground Always 1 MΩ or higher
Y3-1 (GND) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK DTC

NG

13.CHECK FLOOR WIRE
11.CHECK DTC
a.
B521687C01
0.385,1.24 0.823,1.698 0.438,0.458 10 false *1 2.635,0.979 3.094,1.76 0.458,0.781 10 false *2 2.323,1.25 2.781,2.031 0.458,0.781 10 false A 2.167,1.25 2.625,2.031 0.458,0.781 10 false B 1.552,1.25 2.01,2.031 0.458,0.781 10 false C 1.396,1.25 1.854,2.031 0.458,0.781 10 false D 0.781,1.24 1.24,2.021 0.458,0.781 10 false E 0.625,1.24 1.083,2.021 0.458,0.781 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and seat position airbag sensor.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653 is not output.


HINT:

Codes other than DTC B1653 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG

12.CHECK SEAT POSITION AIRBAG SENSOR
12.CHECK SEAT POSITION AIRBAG SENSOR
a.
B521687C01
0.385,1.24 0.823,1.698 0.438,0.458 10 false *1 2.635,0.979 3.094,1.76 0.458,0.781 10 false *2 2.323,1.25 2.781,2.031 0.458,0.781 10 false A 2.167,1.25 2.625,2.031 0.458,0.781 10 false B 1.552,1.25 2.01,2.031 0.458,0.781 10 false C 1.396,1.25 1.854,2.031 0.458,0.781 10 false D 0.781,1.24 1.24,2.021 0.458,0.781 10 false E 0.625,1.24 1.083,2.021 0.458,0.781 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Replace the seat position airbag sensor with a known good one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the power switch off.


h.

Turn the power switch on (IG), and wait for at least 60 seconds.


i.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653 is not output.


HINT:

Codes other than DTC B1653 may be output at this time, but they are not related to this check.



j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



l.

Restore the seat position airbag sensor that was installed for testing to its original location.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

NG

13.CHECK FLOOR WIRE
a.
B521688C02
0.573,0.521 1.01,0.792 0.438,0.271 0.292,3.677 0.677,3.927 0.385,0.25 0.833,4.271 1.01,3.875 true 1.51,4.271 1.302,3.875 true 2.396,1.948 2.729,1.948 false 1.188,1.25 2.177,1.521 true 2.667,1.24 2.313,1.51 true 0.906,2.646 1.073,2.646 1.073,2.646 1.073,2.979 false 1.781,2.635 1.948,2.635 1.948,2.635 1.948,2.969 false 0.625,0.573 1.063,0.792 0.438,0.219 10 false M103 0.521,0.208 1.063,0.604 0.542,0.396 10 false *a 0.25,3.448 0.792,3.844 0.542,0.396 10 false *b 0.198,2.917 0.615,3.271 0.417,0.354 10 false *1 0.75,2.573 1.167,2.927 0.417,0.354 10 false *3 2.823,2.656 3.24,3.01 0.417,0.354 10 false *2 2.5,2.917 2.917,3.271 0.417,0.354 10 false A 2.208,2.917 2.625,3.271 0.417,0.354 10 false B 1.625,2.927 2.042,3.281 0.417,0.354 10 false C 1.333,2.927 1.75,3.281 0.417,0.354 10 false D 0.74,2.927 1.156,3.281 0.417,0.354 10 false E 0.448,2.927 0.865,3.281 0.417,0.354 10 false F 0.344,3.719 0.688,3.969 0.344,0.25 10 false MY2 1.385,4.281 2.073,4.615 0.688,0.333 10 false RSP+ 0.677,4.281 1.271,4.594 0.594,0.313 10 false RSP- 0.813,1.167 1.302,1.719 0.49,0.552 10 false RSP- 2.708,1.167 3.292,1.75 0.583,0.583 10 false RSP+ 2.771,1.865 3.313,2.26 0.542,0.396 10 false *5 1.625,2.563 2.042,2.917 0.417,0.354 10 false *4
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Front Seat Wire RH
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the floor wire connector from the front seat wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
MY2-2 (RSP+) - Body ground Power switch on (IG) Below 1 V
MY2-1 (RSP-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 32 (RSP+) and 31 (RSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MY2-2 (RSP+) - MY2-1 (RSP-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MY2-2 (RSP+) - MY2-1 (RSP-) Always 1 MΩ or higher
MY2-2 (RSP+) - Body ground Always 1 MΩ or higher
MY2-1 (RSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE