Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2019.09
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0304666 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light does not Come ON  


DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the power switch is turned from off to on (IG), and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

If a malfunction occurs in the airbag sensor assembly, combination meter assembly or wire harness connected to the airbag sensor assembly or combination meter assembly, the SRS warning light turns on.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.

When the auxiliary battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not stored in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly via CAN communication.

WIRING DIAGRAM

C422914E02
0.135,1.229 1.615,1.552 1.479,0.323 10 false from IG2-NO. 2 Relay 0.604,1.792 1.479,2.177 0.875,0.385 10 false from Auxiliary Battery 2.917,0.563 4.271,0.792 1.354,0.229 10 false from IG2-NO. 2 Relay 4.927,0.729 5.677,0.948 0.75,0.219 10 false A/BAG-IG2 1.906,1.969 2.979,2.167 1.073,0.198 10 false ECU-DCC NO. 2 0.781,4.167 2.646,4.479 1.865,0.313 10 false : CAN Communication Line 5.896,3.771 6.792,4.146 0.896,0.375 10 false Airbag Sensor Assembly 5.906,3.615 6.302,3.854 0.396,0.24 10 false F150 2.875,3.594 3.271,3.833 0.396,0.24 10 false F4 2.875,3.75 4.083,4.281 1.208,0.531 10 false Combination Meter Assembly 3.115,1.26 3.469,1.51 0.354,0.25 10 false IG+ 3.115,1.823 3.469,2.073 0.354,0.25 10 false B 3.104,2.365 3.458,2.615 0.354,0.25 10 false ET 3.594,1.25 4.083,1.49 0.49,0.24 10 false CANH 3.615,1.802 4.104,2.042 0.49,0.24 10 false CANL 6.052,1.25 6.542,1.49 0.49,0.24 10 false CANH 6.063,1.813 6.552,2.052 0.49,0.24 10 false CANL 6.063,0.573 6.417,0.823 0.354,0.25 10 false IG2 6.073,2.365 6.427,2.615 0.354,0.25 10 false E1 6.073,2.875 6.427,3.125 0.354,0.25 10 false E2 2.833,1.156 3.104,1.406 0.271,0.25 10 false 39 2.854,1.719 3.125,1.969 0.271,0.25 10 false 40 2.844,2.26 3.115,2.51 0.271,0.25 10 false 21 5.781,0.49 6.052,0.74 0.271,0.25 10 false 36 5.781,2.25 6.052,2.5 0.271,0.25 10 false 33 5.792,2.771 6.063,3.021 0.271,0.25 10 false 32 4.083,1.104 4.354,1.354 0.271,0.25 10 false 32 4.094,1.667 4.365,1.917 0.271,0.25 10 false 31 5.771,1.656 6.042,1.906 0.271,0.25 10 false 27 5.781,1.115 6.052,1.365 0.271,0.25 10 false 26 2.125,1.406 3.031,1.656 0.906,0.25 10 false METER-IG2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the auxiliary battery.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR

NG

2.CHECK CONNECTOR
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the combination meter assembly.


e.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE CONNECTOR

3.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)
a.
C241761C42
0.25,0.417 0.667,0.667 0.417,0.25 2.615,2.021 2.927,1.76 true 3.167,1.958 3.073,1.76 true 0.865,1.677 0.583,1.427 true 0.083,0.052 0.51,0.406 0.427,0.354 10 false *a 2.365,1.99 2.729,2.156 0.365,0.167 10 false IG+ 3.177,1.979 3.375,2.146 0.198,0.167 10 false B 0.344,1.323 0.646,1.594 0.302,0.271 10 false ET 0.385,0.458 0.76,0.74 0.375,0.281 10 false F4
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F4-39 (IG+) - Body ground Power switch on (IG) 11 to 14 V
F4-40 (B) - Body ground Always 11 to 14 V



d.

Turn the power switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-21 (ET) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SRS WARNING LIGHT

NG

REPAIR OR REPLACE WIRE HARNESS

4.CHECK SRS WARNING LIGHT
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



b.

Connect the connector to the combination meter assembly.


c.

Disconnect the connector from the airbag sensor assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG) and check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.


HINT:

The primary check period is approximately 6 seconds after the power switch is turned on (IG).



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY