Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2019.09
RM32K0E _56 Audio / Visual / Telematics _060599 PARK ASSIST / MONITORING _0410446 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

DTC C1622 is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Open or Short Circuit in Back Camera Signal Open or short in the rear television camera signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E372776E15
1.844,0.594 2.26,0.854 0.417,0.26 10 false CB+ 1.844,0.99 2.26,1.25 0.417,0.26 10 false CV+ 1.719,1.802 2.24,2.073 0.521,0.271 10 false CGND 3.51,1.958 3.927,2.219 0.417,0.26 10 false * 3.646,3.323 4.76,3.583 1.115,0.26 10 false *: Shielded 0.635,2.635 1.052,2.896 0.417,0.26 10 false S11 0.635,2.781 3.042,3.26 2.406,0.479 10 false Rear Television Camera Assembly 4.99,2.646 5.406,2.906 0.417,0.26 10 false M116 4.979,2.802 6.344,3.167 1.365,0.365 10 false Parking Assist ECU 4.823,0.5 5.24,0.76 0.417,0.26 10 false 8 4.76,0.896 5.177,1.156 0.417,0.26 10 false 11 4.75,1.313 5.167,1.573 0.417,0.26 10 false 35 4.75,1.708 5.167,1.969 0.417,0.26 10 false 25 2.198,0.5 2.615,0.76 0.417,0.26 10 false 6 2.208,1.688 2.625,1.948 0.417,0.26 10 false 5 5,0.583 5.417,0.844 0.417,0.26 10 false CB+ 1.865,1.385 2.281,1.646 0.417,0.26 10 false CV- 5,1.385 5.417,1.646 0.417,0.26 10 false CV- 5,0.979 5.417,1.24 0.417,0.26 10 false CV+ 5,1.792 5.521,2.063 0.521,0.271 10 false CGND 2.208,1.302 2.625,1.563 0.417,0.26 10 false 2 2.208,0.896 2.625,1.156 0.417,0.26 10 false 3 5,2.198 5.521,2.469 0.521,0.271 10 false SGND 4.75,2.104 5.167,2.365 0.417,0.26 10 false 12

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the S11 rear television camera assembly connector.


b.

Disconnect the M116 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S11-6 (CB+) - M116-8 (CB+) Always Below 1 Ω
S11-3 (CV+) - M116-11 (CV+) Always Below 1 Ω
S11-2 (CV-) - M116-35 (CV-) Always Below 1 Ω
S11-5 (CGND) - M116-25 (CGND) Always Below 1 Ω
S11-6 (CB+) or M116-8 (CB+) - Body ground Always 10 kΩ or higher
S11-3 (CV+) or M116-11 (CV+) - Body ground Always 10 kΩ or higher
S11-2 (CV-) or M116-35 (CV-) - Body ground Always 10 kΩ or higher
S11-5 (CGND) or M116-25 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (CV-, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (CV-, CGND)
a.

Disconnect the M116 parking assist ECU connector.


b.
E330226C97
1.458,0.198 1.885,0.438 0.427,0.24 1.99,1.156 2.25,1.74 true 1.302,1.146 1.083,1.688 true 1.5,0.219 1.875,0.375 0.375,0.156 10 false M116 0.115,0.063 0.313,0.24 0.198,0.177 10 false *a 2.198,1.792 2.615,1.948 0.417,0.156 10 false CGND 0.875,1.729 1.292,1.885 0.417,0.156 10 false CV-
*a Component without harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-35 (CV-) - Body ground Always Below 1 Ω
M116-25 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

3.CHECK PARKING ASSIST ECU (CB+, CGND)
a.
E403271C53
1.625,0.646 2.073,0.865 0.448,0.219 2.469,2.365 2.271,1.646 true 2.271,1.469 2.406,0.844 true 1.688,0.667 2.302,0.865 0.615,0.198 10 false M116 0.115,0.083 0.573,0.281 0.458,0.198 10 false *a 2.375,2.448 2.833,2.646 0.458,0.198 10 false CGND 2.354,0.646 2.813,0.844 0.458,0.198 10 false CB+
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M116-25 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M116-8 (CB+) - M116-25 (CGND) Power switch on (IG) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)

NG

4.CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)
a.

Remove the parking assist ECU with the connector still connected.


b.
E403271C54
1.625,0.646 2.073,0.865 0.448,0.219 1.552,1.458 1.229,0.948 true 2.75,1.479 2.885,0.854 true 1.688,0.667 2.302,0.865 0.615,0.198 10 false M116 0.115,0.083 0.573,0.281 0.458,0.198 10 false *a 2.917,0.729 3.375,0.927 0.458,0.198 10 false GND1 0.896,0.833 1.354,1.031 0.458,0.198 10 false CV+
*a Component with harness connected
(Parking Assist ECU)


Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:
E265840C28
0.854,1.99 1.115,1.583 true 1.458,1.979 1.24,1.469 true 1.51,4.125 1.281,3.542 true 0.854,4.146 1.146,3.604 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.646,4.073 1.01,4.333 0.365,0.26 10 false *c 0.677,1.958 1.042,2.219 0.365,0.26 10 false *c 1.458,1.969 1.823,2.229 0.365,0.26 10 false *d 1.479,4.115 1.844,4.375 0.365,0.26 10 false *d
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


·

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.

·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).



Measurement Condition
Item Content
Terminal No. (Symbol) M116-11 (CV+) - M116-25 (CGND)
Tool Setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), panoramic view monitor system operating

OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG