DTC C1681 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the front television camera assembly to the parking assist ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1681 | Front Camera Feedback Malfunction | Front television camera power supply failure | ·
Harness or connector ·
Front television camera assembly ·
Parking assist ECU |
When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION
Disconnect the M116 parking assist ECU connector.
Disconnect the B17 front television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-7 (BCB+) - B17-6 (BCB+) | Always | Below 1 Ω |
| M116-33 (BCV+) - B17-3 (BCV+) | Always | Below 1 Ω |
| M116-10 (BCV-) - B17-2 (BCV-) | Always | Below 1 Ω |
| M116-24 (BGND) - B17-5 (BGND) | Always | Below 1 Ω |
| M116-34 (SGND) - Body ground | Always | 10 kΩ or higher |
| M116-7 (BCB+) or B17-6 (BCB+) - Body ground | Always | 10 kΩ or higher |
| M116-33 (BCV+) or B17-3 (BCV+) - Body ground | Always | 10 kΩ or higher |
| M116-10 (BCV-) or B17-2 (BCV-) - Body ground | Always | 10 kΩ or higher |
| M116-24 (BGND) or B17-5 (BGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M116 parking assist ECU connector.
| *a | Component without harness connected
(Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-24 (BGND) - Body ground | Always | Below 1 Ω |
| M116-10 (BCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M116-24 (BGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M116-7 (BCB+) - M116-24 (BGND) | Power switch on (IG) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
| *a | Component with harness connected
(Parking Assist ECU) |
Using an oscilloscope, check the waveform of the front television camera assembly.
| *a | Waveform 1 (camera lens not covered, displaying an image) |
| *b | Waveform 2 (camera lens covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
The video waveform changes according to the image sent by the front television camera assembly.
The video waveform is constantly output when the power switch is on (ACC).
| Item | Content |
|---|---|
| Terminal No. (Symbol) | M116-33 (BCV+) - M116-24 (BGND) |
| Tool Setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Power switch on (IG), panoramic view monitor system operating |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Front)>REMOVAL