The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Telephone microphone signal is lost. | ·
Map light assembly (telephone microphone assembly) ·
Radio and display receiver assembly ·
Harness or connector |
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for TMMT Made | A |
| for TMC Made | B |
A
B
Disconnect the F131 radio and display receiver assembly connector.
Disconnect the R2 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-25 (SNS2) - R2-1 (SNS2) | Always | Below 1 Ω |
| F131-22 (MIN-) - R2-7 (MCO-) | Always | Below 1 Ω |
| F131-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| F131-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly (telephone microphone assembly).
| *a | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SNS2) - 7 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
NG
Disconnect the F131 radio and display receiver assembly connector.
Disconnect the R2 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-25 (SNS2) - R2-1 (SNS2) | Always | Below 1 Ω |
| F131-22 (MIN-) - R2-7 (MCO-) | Always | Below 1 Ω |
| F131-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| F131-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
| *a | Component without harness connected
(Telephone Microphone Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SNS2) - 2 (MIC-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMC Made)>REMOVAL
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R2-1 (SNS2) - B-1 | Always | Below 1 Ω |
| R2-7 (MCO-) - B-2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
NG