Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2019.09–2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0302427 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

for TMMT Made
E381473E23
0.333,2.438 0.75,2.667 0.417,0.229 10 false R2 0.333,2.594 2.313,3.208 1.979,0.615 10 false Map Light Assembly (Telephone Microphone Assembly) 5.427,2.927 5.844,3.156 0.417,0.229 10 false F131 5.406,3.104 7.094,3.719 1.688,0.615 10 false Radio and Display Receiver Assembly 5.948,2.625 6.427,2.854 0.479,0.229 10 false SGND 5.958,1.583 6.375,1.813 0.417,0.229 10 false MIN+ 5.958,1.052 6.49,1.281 0.531,0.229 10 false MACC 5.958,0.531 6.375,0.76 0.417,0.229 10 false SNS2 5.677,0.438 6.094,0.667 0.417,0.229 10 false 25 5.677,0.969 6.094,1.198 0.417,0.229 10 false 23 5.688,1.49 6.104,1.719 0.417,0.229 10 false 21 5.677,2 6.094,2.229 0.417,0.229 10 false 22 5.677,2.521 6.094,2.75 0.417,0.229 10 false 24 1.677,1.99 2.094,2.219 0.417,0.229 10 false 7 1.677,1.458 2.094,1.688 0.417,0.229 10 false 8 1.677,0.927 2.094,1.156 0.417,0.229 10 false 9 1.677,0.427 2.094,0.656 0.417,0.229 10 false 1 1.135,1.583 1.635,1.792 0.5,0.208 10 false MCO+ 1.146,2.104 1.646,2.313 0.5,0.208 10 false MCO- 1.125,1.042 1.656,1.271 0.531,0.229 10 false MACC 5.979,2.094 6.396,2.323 0.417,0.229 10 false MIN- 1.156,0.521 1.573,0.75 0.417,0.229 10 false SNS2 3.438,2.354 4.25,2.688 0.813,0.333 10 false (Shielded)

for TMC Made
E431711E01
0.229,3.125 0.646,3.354 0.417,0.229 10 false R2 0.302,2.365 2.281,2.979 1.979,0.615 10 false Telephone Microphone Assembly 5.469,2.792 5.885,3.021 0.417,0.229 10 false F131 5.469,2.969 7.156,3.583 1.688,0.615 10 false Radio and Display Receiver Assembly 5.906,2.49 6.385,2.719 0.479,0.229 10 false SGND 5.896,1.469 6.313,1.698 0.417,0.229 10 false MIN+ 5.906,0.958 6.438,1.188 0.531,0.229 10 false MACC 5.896,0.417 6.313,0.646 0.417,0.229 10 false SNS2 5.656,0.302 6.073,0.531 0.417,0.229 10 false 25 5.656,0.823 6.073,1.052 0.417,0.229 10 false 23 5.656,1.354 6.073,1.583 0.417,0.229 10 false 21 5.667,1.865 6.083,2.094 0.417,0.229 10 false 22 5.656,2.375 6.073,2.604 0.417,0.229 10 false 24 2.281,1.823 2.698,2.052 0.417,0.229 10 false 7 2.271,1.323 2.688,1.552 0.417,0.229 10 false 8 2.281,0.792 2.698,1.021 0.417,0.229 10 false 9 2.271,0.302 2.688,0.531 0.417,0.229 10 false 1 1.771,1.344 2.271,1.552 0.5,0.208 10 false MCO+ 1.802,1.854 2.302,2.063 0.5,0.208 10 false MCO- 1.813,0.813 2.344,1.042 0.531,0.229 10 false MACC 5.917,1.979 6.333,2.208 0.417,0.229 10 false MIN- 1.792,0.302 2.208,0.531 0.417,0.229 10 false SNS2 3.438,2.354 4.25,2.688 0.813,0.333 10 false (Shielded) 0.24,3.292 1.948,3.552 1.708,0.26 10 false Map Light Assembly 1.521,0.813 1.938,1.042 0.417,0.229 10 false 5 1.521,1.323 1.938,1.552 0.417,0.229 10 false 3 1.542,1.844 1.958,2.073 0.417,0.229 10 false 2 1.531,0.302 1.948,0.531 0.417,0.229 10 false 1

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E277821

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

NG

2.CONFIRM MODEL
2.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for TMMT Made A
for TMC Made B




A

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

B

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F131 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-25 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F131-23 (MACC) - R2-9 (MACC) Always Below 1 Ω
F131-21 (MIN+) - R2-8 (MCO+) Always Below 1 Ω
F131-22 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F131-25 (SNS2) - Body ground Always 10 kΩ or higher
F131-23 (MACC) - Body ground Always 10 kΩ or higher
F131-21 (MIN+) - Body ground Always 10 kΩ or higher
F131-22 (MIN-) - Body ground Always 10 kΩ or higher
F131-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F131 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.
E366062C58
1.427,0.198 1.917,0.479 0.49,0.281 2.01,1.354 2.844,1.646 true 2.5,1.802 1.906,1.365 true 1.979,1.885 1.802,1.375 true 1.521,0.24 1.896,0.438 0.375,0.198 10 false F131 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 2.813,1.656 3.271,1.854 0.458,0.198 10 false MIN- 1.885,1.917 2.385,2.146 0.5,0.229 10 false SGND 2.354,1.823 2.979,2.021 0.625,0.198 10 false MACC
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F131-23 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-24 (SGND) - Body ground Always Below 1 Ω
F131-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMMT Made)>REMOVAL


b.
E358190C06
2.281,1.094 2.552,0.49 true 2.292,1.427 2.583,1.771 true 0.25,0.198 0.563,0.396 0.313,0.198 10 false *a 2.479,0.302 2.948,0.521 0.469,0.219 10 false SNS2 2.583,1.771 3.219,1.958 0.635,0.188 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

6.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F131 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Turn the power switch on (ACC).


d.
E358189C03
1.542,0.49 1.969,0.75 0.427,0.26 2.188,1.75 2.708,2.177 true 1.99,1.781 2.208,2.385 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.646,0.521 1.958,0.719 0.313,0.198 10 false R2 2.76,2.188 3.198,2.458 0.438,0.271 10 false MCO- 2.115,2.427 2.604,2.698 0.49,0.271 10 false MCO+
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector.


e.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the F131 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-25 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F131-23 (MACC) - R2-9 (MACC) Always Below 1 Ω
F131-21 (MIN+) - R2-8 (MCO+) Always Below 1 Ω
F131-22 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F131-25 (SNS2) - Body ground Always 10 kΩ or higher
F131-23 (MACC) - Body ground Always 10 kΩ or higher
F131-21 (MIN+) - Body ground Always 10 kΩ or higher
F131-22 (MIN-) - Body ground Always 10 kΩ or higher
F131-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT MAP LIGHT ASSEMBLY
a.

b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


c.
E431698C02
1.51,1.792 1.906,2.052 0.396,0.26 1.458,0.188 1.854,0.448 0.396,0.26 2.104,0.979 2.5,0.604 true 1.229,1.635 1.792,1.229 true 1.938,1.26 2.188,1.656 true 2.104,1.219 2.552,1.448 true 1.552,0.229 2.01,0.427 0.458,0.198 10 false R2 1.635,1.844 2.094,2.042 0.458,0.198 10 false B 2.563,0.479 3.177,0.677 0.615,0.198 10 false SNS2 2.219,1.677 2.833,1.875 0.615,0.198 10 false MCO+ 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 2.604,1.375 3.219,1.573 0.615,0.198 10 false MCO- 0.99,1.646 1.604,1.844 0.615,0.198 10 false MACC
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-9 (MACC) - B-5 Always Below 1 Ω
R2-7 (MCO-) - B-2 Always Below 1 Ω
R2-1 (SNS2) - B-1 Always Below 1 Ω
R2-8 (MCO+) - B-3 Always Below 1 Ω
R2-9 (MACC) or B-5 - Body ground Always 10 kΩ or higher
R2-7 (MCO-) or B-2 - Body ground Always 10 kΩ or higher
R2-8 (MCO+) or B-3 - Body ground Always 10 kΩ or higher
R2-7 (MCO-) or B-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F131 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly connector.


c.
E366062C58
1.427,0.198 1.917,0.479 0.49,0.281 2.01,1.354 2.844,1.646 true 2.5,1.802 1.906,1.365 true 1.979,1.885 1.802,1.375 true 1.521,0.24 1.896,0.438 0.375,0.198 10 false F131 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 2.813,1.656 3.271,1.854 0.458,0.198 10 false MIN- 1.885,1.917 2.385,2.146 0.5,0.229 10 false SGND 2.354,1.823 2.979,2.021 0.625,0.198 10 false MACC
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F131-23 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-24 (SGND) - Body ground Always Below 1 Ω
F131-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT TELEPHONE MICROPHONE ASSEMBLY

NG

10.INSPECT TELEPHONE MICROPHONE ASSEMBLY
a.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.
E339287C02
1.792,1.76 1.99,1.271 true 2.719,1.74 2.51,1.281 true 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.646,1.813 2.26,2.01 0.615,0.198 10 false MIC- 2.573,1.792 3.188,1.99 0.615,0.198 10 false SNS2
*a Component without harness connected
(Telephone Microphone Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 2 (MIC-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.INSPECT MAP LIGHT ASSEMBLY

NG

REPLACE TELEPHONE MICROPHONE ASSEMBLY

11.INSPECT MAP LIGHT ASSEMBLY
a.

Reconnect the F131 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly connector.


c.

Turn the power switch on (ACC).


d.
E358189C03
1.542,0.49 1.969,0.75 0.427,0.26 2.188,1.75 2.708,2.177 true 1.99,1.781 2.208,2.385 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.646,0.521 1.958,0.719 0.313,0.198 10 false R2 2.76,2.188 3.198,2.458 0.438,0.271 10 false MCO- 2.115,2.427 2.604,2.698 0.49,0.271 10 false MCO+
*a Component with harness connected
(Map Light Assembly)


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly connector.


e.

Check the waveform of the map light assembly using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly is output. A
A waveform synchronized with the voice input to the map light assembly is not output. B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B