This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2284 | Brake Signal Malfunction | The brake signal sent via direct line and the brake signal sent via CAN communication do not match. (1-trip detection logic*) | ·
AM2 fuse ·
STOP fuse ·
Stop light switch assembly ·
Electronically controlled brake system ·
Certification ECU (smart key ECU assembly) ·
Wire harness or connector |
DTC Output Confirmation Operation:
Connect the cable to the negative (-) auxiliary battery terminal, release the brake pedal and wait at least 20 seconds. Then depress the brake pedal for 20 seconds or more. |
*: Only detected while a malfunction is present and the power switch is on (IG).
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| With the electrical key transmitter sub-assembly in the cabin, even if an hybrid control system start operation is performed, the hybrid control system does not start (the key indicator display is not displayed on the multi-information display). However, the hybrid control system can be started by turning the power switch on (ACC) and then pressing and holding it.
·
If there is a malfunction when the brake signal sent via direct line is on, the hybrid control system can be started by pressing the power switch with the brake pedal released. ·
If there is a malfunction when the brake signal sent via direct line is off, the hybrid control system cannot be started by pressing the power switch with the brake pedal depressed. |
- |
| DTC No. | Data List and Active Test |
|---|---|
| B2284 | Power Source Control
·
Stop Light Switch1 ABS/VSC/TRC
·
Stop Light SW |
When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Start Function) Precaution.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Switch1 | State of brake pedal | OFF or ON | OFF: Brake pedal released
ON: Brake pedal depressed |
·
Use this item to determine if the stop light switch assembly is malfunctioning. ·
The hybrid control system cannot be started when this item is OFF. ·
If the stop light switch assembly is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time. |
| Tester Display |
|---|
| Stop Light Switch1 |
The GTS display changes correctly in response to the brake pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M67 certification ECU (smart Key ECU assembly) connector.
Disconnect the A91 stop light switch assembly connector.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A91-7 (B) - Body ground | Power switch off | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M67-25 (STP1) - A91-3 (L) | Always | Below 1 Ω |
| A91-2 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the M67 certification ECU (smart Key ECU assembly) connectors.
Reconnect the A91 stop light switch assembly connector.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M67-25 (STP1) - Body ground | Brake pedal released → depressed | 1 V or less → 9 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG