Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2019.09–2020.08
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Headlight ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Headlight ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Headlight swivel (AFS)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Headlight swivel (AFS)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Headlight swivel (AFS)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "AFS ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Headlight ECU sub-assembly LH branch line or connector

·

Power source circuit of Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly LH ground circuit

·

Headlight ECU sub-assembly LH



WIRING DIAGRAM

C366185E11
1.615,0.531 1.76,0.729 0.146,0.198 10 false 3 1.625,1.073 1.844,1.281 0.219,0.208 10 false 14 0.083,1.542 0.438,1.75 0.354,0.208 10 false F114 0.073,1.698 2,1.917 1.927,0.219 10 false No. 3 CAN Junction Connector 2.188,2.188 3.531,2.396 1.344,0.208 10 false from IG1-NO. 1 Relay 2.281,2.729 3.531,2.938 1.25,0.208 10 false from H-LP LH Relay 4.344,2.375 5.313,2.583 0.969,0.208 10 false ECU-IG1 NO. 3 5.573,3.698 5.938,3.885 0.365,0.188 10 false A95 5.563,3.854 6.833,4.26 1.271,0.406 10 false Headlight ECU Sub-assembly LH 5.531,0.531 5.75,0.74 0.219,0.208 10 false 24 5.531,1.073 5.75,1.281 0.219,0.208 10 false 23 5.604,2.146 5.823,2.354 0.219,0.208 10 false 4 5.542,2.667 5.76,2.875 0.219,0.208 10 false 13 5.531,3.219 5.75,3.427 0.219,0.208 10 false 12 5.813,0.604 6.24,0.813 0.427,0.208 10 false CANH 5.802,1.156 6.229,1.365 0.427,0.208 10 false CANL 5.792,2.219 6.219,2.427 0.427,0.208 10 false IG 5.792,2.75 6.219,2.958 0.427,0.208 10 false ECUB 5.792,3.302 6.219,3.51 0.427,0.208 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (HEADLIGHT ECU SUB-ASSEMBLY LH BRANCH LINE)
a.
C308332C32
1.458,0.167 1.958,0.417 0.5,0.25 2.833,1.833 2.635,1.354 true 2.25,1.833 2.458,1.354 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.573,0.188 2.031,0.385 0.458,0.198 10 false A95 2.667,1.865 3.281,2.063 0.615,0.198 10 false CANH 2.083,1.865 2.698,2.063 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A95-24 (CANH) - A95-23 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A95-12 (GND) - Body ground Always Below 1 Ω



b.
C308332C33
1.458,0.167 1.958,0.417 0.5,0.25 2.083,1.833 1.833,1.229 true 1.5,1.833 1.281,1.302 true 0.583,1.833 0.823,1.302 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.573,0.188 2.031,0.385 0.458,0.198 10 false A95 1.344,1.854 1.958,2.052 0.615,0.198 10 false ECUB 0.448,1.854 1.063,2.052 0.615,0.198 10 false GND 2.052,1.854 2.365,2.052 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A95-4 (IG) - Body ground Power switch on (IG) 11 to 14 V
A95-13 (ECUB) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)