Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2019.09
RM32K0E _59 Vehicle Exterior _061162 LIGHTING (EXT) _0303092 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM C

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  B2416  Height Control Sensor Malfunction  B241A  Rear Height Control Sensor  


DESCRIPTION

This DTC is stored when the headlight ECU sub-assembly LH detects a malfunction in the rear height control sensor sub-assembly LH power source circuit or rear height control sensor sub-assembly LH circuit. The headlight ECU sub-assembly LH stores DTC B2416 and/or B241A.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2416 Height Control Sensor Malfunction Any of the following conditions is met:
·

Malfunction in rear height control sensor sub-assembly LH

·

Open in rear height control sensor sub-assembly LH power source circuit

·

Short in rear height control sensor sub-assembly LH power source circuit


·

Rear height control sensor sub-assembly LH

·

Headlight ECU sub-assembly LH

·

Harness or connector


-
B241A Rear Height Control Sensor Any of the following conditions is met:
·

Malfunction in rear height control sensor sub-assembly LH

·

Open in rear height control sensor sub-assembly LH circuit

·

Short in rear height control sensor sub-assembly LH circuit


·

Rear height control sensor sub-assembly LH

·

Headlight ECU sub-assembly LH

·

Harness or connector


-

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch ON ○ ○ ○
Malfunction Status Malfunction in rear height control sensor sub-assembly LH ○ - -
Open in rear height control sensor sub-assembly LH power source circuit - ○ -
Short in rear height control sensor sub-assembly LH power source circuit - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

E234217E70
4.354,0.448 4.719,0.604 0.365,0.156 10 false SBR 4.344,0.958 4.771,1.146 0.427,0.188 10 false SHRL 4.354,1.469 4.729,1.625 0.375,0.156 10 false SGR 4.104,0.354 4.406,0.563 0.302,0.208 10 false 16 4.104,0.854 4.49,1.115 0.385,0.26 10 false 17 4.094,1.354 4.479,1.635 0.385,0.281 10 false 15 2.865,0.354 3.021,0.5 0.156,0.146 10 false 3 2.854,0.854 3.01,1 0.156,0.146 10 false 2 2.854,1.354 3.01,1.5 0.156,0.146 10 false 1 1.042,2.052 2.75,2.583 1.708,0.531 10 false Rear Height Control Sensor Sub-assembly LH 1.063,1.875 1.323,2.135 0.26,0.26 10 false O2 4.167,2.042 6.51,2.292 2.344,0.25 10 false Headlight ECU Sub-assembly LH 4.188,1.854 4.531,2.052 0.344,0.198 10 false A16 2.448,1.458 2.906,1.656 0.458,0.198 10 false SHG 2.354,0.958 2.813,1.156 0.458,0.198 10 false SHRR 2.448,0.458 2.906,0.656 0.458,0.198 10 false SHB

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing this inspection, check that the rear height control sensor sub-assembly LH is installed correctly.

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION

·

If any of the following are performed, it is necessary to initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION

-

Replacement of the rear height control sensor sub-assembly LH

-

Removal/installation of the rear height control sensor sub-assembly LH

-

Work that changes the vehicle height such as replacement of suspension components




PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HIGH BEAM SYSTEM>DTC CHECK / CLEAR

Body Electrical > AFS > Clear DTCs
50002 165

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the power switch to on (IG).


b.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > AFS > Trouble Codes
50001 165
OK:

DTC B2416 or B241A are not output.



Result:
Proceed to
OK
NG



OK

NG

3.READ VALUE USING GTS
3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / AFS / Data List.


e.

Read the Data List according to the display on the GTS.

OK:

Normal condition listed above is displayed.


Body Electrical > AFS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Rear height control sensor sub-assembly LH power supply value 0.00 to 6.25 V 4.61 to 5.00 V -
Rr Height Sens Signal Val Rear height control sensor sub-assembly LH signal value 0.00 to 5.00 V 0.50 to 4.50 V Value changes according to vehicle height
Body Electrical > AFS > Data List
Tester Display
Height Sens Pw Supply Val
Rr Height Sens Signal Val
50003 165 8,10

Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH)
a.

Disconnect the A95 headlight ECU sub-assembly LH connector.


b.

Disconnect the O2 rear height control sensor sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A95-16 (SBR) - O2-3 (SHB) Always Below 1 Ω
A95-17 (SHRL) - O2-2 (SHRR) Always Below 1 Ω
A95-15 (SGR) - O2-1 (SHG) Always Below 1 Ω
A95-16 (SBR) or O2-3 (SHB) - Body ground Always 10 kΩ or higher
A95-17 (SHRL) or O2-2 (SHRR) - Body ground Always 10 kΩ or higher
A95-15 (SGR) or O2-1 (SHG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
a.

Remove the rear height control sensor sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL


b.

Inspect the rear height control sensor sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION

OK:

Rear height control sensor sub-assembly LH is normal.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH