Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › IGNITION SYSTEM › from 2019.09
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295699 IGNITION SYSTEM G

2ZR-FXE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.PERFORM SPARK TEST

CAUTION:
·
A345225

When working near the engine room while the engine has started or the power source mode is power switch on (IG), do not touch the rotating components such as the fan, etc.

·

Touching rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.

·
A344783

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust manifold.

·

Touching high-temperature areas such as the engine and exhaust manifold could result in burns.



HINT:

Perform "Inspection After Repair" after replacing a spark plug.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Check for DTCs.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

If any DTCs are output, perform troubleshooting in accordance with the procedure for each DTC.



b.

Remove the 4 ignition coil assemblies and 4 spark plugs.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL

NOTICE:

If an ignition coil assembly or spark plug has been struck or dropped, replace it.


HINT:

Arrange the removed parts in the correct order.



c.
A374992

Disconnect the 4 fuel injector assembly connectors.

NOTICE:

Perform this step in order to stop fuel injection to prevent damage to the catalyst due to unburned fuel.



d.
A374993

Install the spark plug to the ignition coil assembly, and then connect the ignition coil assembly connector.


e.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


f.

Ground the spark plug.


g.

Check that spark occurs at each spark plug while the engine is being cranked.

NOTICE:
·

Be sure to ground the spark plugs when checking them.

·

Do not crank the engine for more than 2 seconds.

·

If an ignition coil assembly or spark plug has been struck or dropped, replace it.



HINT:

If spark does not occur, perform the following procedure.



h.

Connect the 4 fuel injector assembly connectors.


i.

Install the 4 spark plugs and 4 ignition coil assemblies.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION

NOTICE:

If an ignition coil assembly or spark plug has been struck or dropped, replace it.


HINT:

Install the same parts to their original positions.





Hide 2.INSPECT IGNITION COIL ASSEMBLY AND SPARK TEST

CAUTION:
·
A345225

When working near the engine room while the engine has started or the power source mode is power switch on (IG), do not touch the rotating components such as the fan, etc.

·

Touching rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.

·
A344783

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust manifold.

·

Touching high-temperature areas such as the engine and exhaust manifold could result in burns.



HINT:

Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR


a.

Check that the ignition coil assembly connector is securely connected.

Result:
Result Action
NG Connect securely
OK Go to next step



b.

Perform a spark test on each ignition coil assembly.

i.

Replace the ignition coil assembly with a known good one.


ii.

Perform the spark test again.

Result:
Result Action
NG Go to next step
OK Replace ignition coil assembly
(Click here)


NOTICE:

If an ignition coil assembly or spark plug has been struck or dropped, replace it.




c.

Perform a spark test on each spark plug.

i.

Replace the spark plug with a known good one.


ii.

Perform the spark test again.

Result:
Result Action
NG Inspect the ignition system
(Click here)
OK Replace spark plug
(Click here)


NOTICE:

If an ignition coil assembly or spark plug has been struck or dropped, replace it.




d.

Connect the 4 fuel injector assembly connectors.


e.

Install the 4 spark plugs and 4 ignition coil assemblies.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION

NOTICE:

If an ignition coil assembly or spark plug has been struck or dropped, replace it.


HINT:

Install the same parts to their original positions.





Hide 19100P 3.INSPECT SPARK PLUG

CAUTION:
·
A345225

When working near the engine room while the engine has started or the power source mode is power switch on (IG), do not touch the rotating components such as the fan, etc.

·

Touching rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.

·
A344783

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust manifold.

·

Touching high-temperature areas such as the engine and exhaust manifold could result in burns.



NOTICE:
·

Be careful not to damage the iridium tip or platinum tip of the spark plug.

·

Check the iridium tip visually as it is easily damaged.

·

Never attempt to adjust the electrode gap of a used spark plug.

·

If a spark plug is extremely dirty with oil, etc., replace it.

·

Replace a spark plug if it is damaged.

·

If a spark plug has been struck or dropped, replace it.

·

When installing a new spark plug, do not remove the protective cap from the spark plug tip until just before installing the spark plug to the engine.



HINT:

Perform "Inspection After Repair" after replacing a spark plug.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
I039522C34
0.708,1.969 1.094,1.917 false 0.563,1.875 0.74,2.042 0.177,0.167 10 false *a
*a Body Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Body ground Always 10 MΩ or higher


HINT:

If a megohmmeter is not available, perform the following simple inspection instead.




b.

Alternative inspection method.

i.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


ii.

Start the engine.

NOTICE:

Do not perform this step when any of the following DTCs are output: P030000, P030027, P030085, P030100, P030200, P030300, P030400 (Cylinder Misfire Detected).



iii.

Quickly accelerate the engine to 2500 rpm 5 times.

NOTICE:

Do not perform this step when any of the following DTCs are output: P030000, P030027, P030085, P030100, P030200, P030300, P030400 (Cylinder Misfire Detected).




v.

Visually check the spark plug.

HINT:

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.




c.

Check the spark plug for any damage to its threads and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Spark Plug Type
DENSO FC16HR-CY9



d.
A126880C06
0.719,1.115 0.885,1.302 0.167,0.188 10 *a
*a Spark Plug Electrode Gap


Check the spark plug electrode gap.

Maximum Electrode Gap for Used Spark Plug:

1.1 mm (0.0433 in.)


NOTICE:

Never attempt to adjust the electrode gap of a used spark plug.


If the electrode gap is more than the maximum, replace the spark plug.

Standard Electrode Gap for New Spark Plug:

0.8 to 0.9 mm (0.0315 to 0.0354 in.)




Hide 4.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION