Home › Engine / Hybrid System › M20A-FXS (FUEL) › FUEL PUMP › from 2020.08
RM32K0E _51 Engine / Hybrid System _083996 M20A-FXS FUEL _0404504 FUEL PUMP A

M20A-FXS FUEL  FUEL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Replacement of fuel pump Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

Keep fuel away from rubber or leather parts.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE REAR SEAT ASSEMBLY

Hide 5.REMOVE NO. 6 WIRING HARNESS PROTECTOR

a.

Remove the No. 6 wiring harness protector from the rear floor service hole cover.


Hide 58325E 6.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A374588C02
1.333,0.479 1.625,0.219 true 1.625,0.125 1.833,0.271 0.208,0.146 10 true *a
*a Protective Tape


Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.


b.
A451689

Disconnect the 2 fuel suction tube with pump and gauge assembly connectors.


Hide 77026A 7.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A451690

Slide the clip and disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel suction tube with pump and gauge assembly.


Hide 77754B 8.DISCONNECT CHARCOAL CANISTER OUTLET HOSE

A451691

a.

Slide the clip and disconnect the charcoal canister outlet hose from the fuel suction tube with pump and gauge assembly.


Hide 77209F 9.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A451692

Disengage the claw to remove the No. 1 fuel tube clamp.


b.
A451693C01
0.583,2.135 0.99,2.01 true 1.188,3.198 1.521,3.198 false 2.24,3.51 2.74,3.51 true 2.229,3.365 2.583,3.365 2.583,3.365 2.583,3.5 true 1.25,1.375 0.958,0.99 true 1.042,2.781 0.719,2.563 true 2.396,2.552 2.021,2.677 true 1.271,3.76 0.99,4.021 false 0.75,0.875 0.958,1.063 0.208,0.188 10 true *3 0.365,2.031 0.552,2.24 0.188,0.208 10 true *2 0.792,3.938 1.104,4.135 0.313,0.198 10 false *1 1.021,3.094 1.333,3.292 0.313,0.198 10 false *2 2.771,3.406 3.083,3.604 0.313,0.198 10 false *5 2.427,2.458 2.74,2.656 0.313,0.198 10 false *4 0.51,2.438 0.823,2.635 0.313,0.198 10 false *a
*1 No. 1 Plate Sub-assembly
*2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly
*4 Fuel Tube Joint
*5 O-ring
*a Nylon Tube
V100135

Pull off
V100136

Pull off


Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube joint by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

·

If the fuel tube joint and No. 1 plate sub-assembly are stuck, push and pull to release them.




Hide 77144 10.REMOVE FUEL PUMP GAUGE RETAINER

a.

Remove the fuel pump gauge retainer.

i.
A440649C01
0.76,0.75 1.188,0.75 true 0.781,0.365 1.292,0.365 true 2.344,0.906 2.615,0.563 2.615,0.563 2.729,0.563 true 2.563,1.177 2.771,1.573 2.771,1.573 2.865,1.573 true 2.229,2.063 2.229,1.365 true 0.969,2.823 1.229,2.823 true 1.25,2.729 1.448,2.948 0.198,0.219 10 true *a 2.917,1.5 3.146,1.708 0.229,0.208 10 true *b 2.146,2.083 2.406,2.323 0.26,0.24 10 true *c 0.604,0.302 0.792,0.5 0.188,0.198 10 true *d 0.583,0.677 0.771,0.875 0.188,0.198 10 true *c 2.76,0.479 2.969,0.677 0.208,0.198 10 true *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.
A440650C01
1.198,1.198 1.5,1.198 false 1.896,1.844 2.188,1.844 true 2.865,2.75 3.042,2.75 true 1.917,2.354 2.042,2.146 2.042,2.146 2.219,2.146 true 1.563,1.583 1.896,1.479 1.896,1.479 2.156,1.479 true 1,1.104 1.167,1.313 0.167,0.208 10 true *a 2.208,1.76 2.385,1.948 0.177,0.188 10 true *b 2.188,1.406 2.406,1.625 0.219,0.219 10 true *e 3.073,2.677 3.24,2.875 0.167,0.198 10 true *c 2.26,2.052 2.469,2.229 0.208,0.177 10 true *d
*a SST (Handle)
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)
*e Extension Bar


Install SST (handle) and an extension bar to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010, 09808-01030, 09808-01090)


iv.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or the fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




v.

While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.



Hide 77020A 11.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A440651

Remove the fuel suction tube set gasket from the fuel tank assembly.