Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304571 DYNAMIC RADAR CRUISE CONTROL SYSTEM Y

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Before performing troubleshooting for the dynamic radar cruise control system, perform troubleshooting for the pre-collision system.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the auxiliary battery voltage.

HINT:

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.


Standard Voltage:

11 to 14 V (Power switch off)



b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (HEALTH CHECK)*
4.CHECK FOR DTCs (HEALTH CHECK)*
a.

Using the GTS, perform a health check.


Result:
Result Proceed to
System DTCs other than DTCs related to the dynamic radar cruise control system (Cruise Control) and dynamic radar cruise control system (Radar Cruise 2) are not output. A
System DTCs other than DTCs related to the dynamic radar cruise control system (Cruise Control) and dynamic radar cruise control system (Radar Cruise 2) are output. B



A

5.CHECK MULTI-INFORMATION DISPLAY

B

GO TO DTC CHART

5.CHECK MULTI-INFORMATION DISPLAY
a.

Check if a warning message is displayed on the multi-information display in the combination meter assembly.

HINT:

If more than one message is displayed, perform each inspection in the order of A, B and C.



Result:
Result Proceed to
"Cruise Control Malfunction Visit Your Dealer" is displayed. A
One of the following warning messages is displayed:
·

"Radar Cruise Control Unavailable See Owner's Manual"

·

"Radar Cruise Control Unavailable"


B
No dynamic radar cruise control system warnings are displayed. C



A

6.CHECK CAN COMMUNICATION SYSTEM*

B

8.CHECK VEHICLE CONTROL HISTORY*

C

11.PROBLEM SYMPTOMS TABLE
6.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check that the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

CAN Bus Check
50007
OK:

CAN communication system is functioning normally.



Result:
Proceed to
OK
NG



OK

7.CHECK FOR DTCs*

NG

7.CHECK FOR DTCs*
a.

Check for DTCs.

Powertrain > Cruise Control > Trouble Codes
50001 399
Powertrain > Radar Cruise2 > Trouble Codes
50001 426

b.

Make a note of any DTCs that are output.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

8.CHECK VEHICLE CONTROL HISTORY*

B

10.RECONFIRM DTCs*
8.CHECK VEHICLE CONTROL HISTORY*
a.

Using the GTS, check for vehicle control history.

Powertrain > Radar Cruise2 > Utility
Tester Display
Vehicle Control History (RoB)
50005 426 55

b.

Record any vehicle control history that is output.


Result:
Result Proceed to
Vehicle control history is not output A
Vehicle control history X2006, X2013, X2015, X2022, X2026 or X2028 is output B
Vehicle control history other than X2006, X2013, X2015, X2022, X2026 or X2028 is output C



A

B

C

9.RECONFIRM VEHICLE CONTROL HISTORY*
9.RECONFIRM VEHICLE CONTROL HISTORY*
a.

Using the GTS, clear the vehicle control history.

Powertrain > Radar Cruise2 > Utility
Tester Display
Vehicle Control History (RoB)
50005 426 55

b.

Recheck for vehicle control history.

Powertrain > Radar Cruise2 > Utility
Tester Display
Vehicle Control History (RoB)
50005 426 55

Result:
Result Proceed to
Vehicle control history is not output A
Vehicle control history is output B



A

B

10.RECONFIRM DTCs*
a.

Clear the DTCs.

Powertrain > Cruise Control > Trouble Codes
50001 399
Powertrain > Radar Cruise2 > Clear DTCs
50002 426

b.

Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.

HINT:

Refer to each corresponding DTC for details on the detection conditions.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART



c.

Recheck for DTCs.

i.

Attempt to duplicate the malfunction and check if the DTCs are output again.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 399
Powertrain > Radar Cruise2 > Trouble Codes
50001 426


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B

GO TO DTC CHART

11.PROBLEM SYMPTOMS TABLE
HINT:

Refer to Problem Symptoms Table.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

12.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*

B

12.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*
NOTICE:

Before checking for millimeter wave radar sensor beam axis misalignment, make sure that the radiator grille and front bumper are correctly installed and have not been damaged or modified.




c.

Using the GTS, check the amount of misalignment.

Body Electrical > Front Radar Sensor > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 429 4405
Standard:
Vertical Direction -5 to 5 deg.
Horizontal Direction -0.6 to 0.6 deg.



Result:
Result Proceed to
The beam axis values are within specification A
The beam axis values are not within specification B



A

B