Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2020.08
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0304576 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Circuit  


DESCRIPTION

If no warnings operate or the system can be set even though the conditions to set the system are not met, the main body ECU (multiplex network body ECU) cannot perform recognition due to a cutoff of the ON signal from the courtesy light switch from the doors or hood or some other problem.

If the theft deterrent system operates when it should not operate, it may be due to a false detection by the intrusion sensor (theft warning ultrasonic sensor) or due to the ON signal being input when there is a short circuit in the courtesy light switch of the doors or hood or some other problem which would cause this to happen.

HINT:

In the following situations, the intrusion sensor (theft warning ultrasonic sensor) may operate and cause the theft deterrent system to operate even when the sensor is normal.

·

The driver locks the doors and walks away from the vehicle while other people, pets, etc. are in the vehicle.

·

There are things which move easily inside the vehicle, such as things hanging inside the vehicle or clothing hanging from the coat hooks.

·

A window is open.

·

The vehicle is parked in a place with a lot of vibration or noise such as a parking garage.

·

The vehicle is being washed using a high-pressure spray gun or an automatic car wash.

·

The vehicle is continuously being struck or is vibrating due to hail or lightning.

·

The vehicle is continuously being subjected to impacts or is vibrating when snow or ice is being removed from the vehicle.

·

A frost prevention sheet which has an aluminum film is moved by wind, etc.



WIRING DIAGRAM

E352020E14
0.656,0.365 2.188,0.667 1.531,0.302 10 false from Auxiliary Battery 3.583,1.208 3.865,1.427 0.281,0.219 10 false +B 3.469,1.781 3.833,2 0.365,0.219 10 false IOUT 1.188,1.729 1.604,1.948 0.417,0.219 10 false GND 3.885,1.219 4.167,1.438 0.281,0.219 10 false 1 3.906,1.781 4.188,2 0.281,0.219 10 false 2 5.375,1.75 5.656,1.969 0.281,0.219 10 false 12 0.958,1.656 1.24,1.875 0.281,0.219 10 false 3 5.646,1.75 6.01,1.969 0.365,0.219 10 false ISIF 5.448,2.708 5.813,2.927 0.365,0.219 10 false F16 5.438,2.875 7.094,3.333 1.656,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 1.656,2.688 3.604,3.104 1.948,0.417 10 false Intrusion Sensor (Theft Warning Ultrasonic Sensor) 1.656,2.521 2.646,2.729 0.99,0.208 10 false R17 2.75,0.552 3.948,0.75 1.198,0.198 10 false ECU-DCC NO. 2

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (INTRUSION SENSOR, INTRUSION SENSOR SOUND DETECT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

HINT:

When performing the above inspection, have the electrical key transmitter sub-assembly in the vehicle exterior detection area to perform certification (this prevents the alarm from sounding).


NOTICE:

Make sure that all windows are closed.



f.

Make a metal-on-metal striking sound (such as by shaking keys) near the intrusion sensor (theft warning ultrasonic sensor) and check the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Sound Detect Sound detection status of the intrusion sensor (theft warning ultrasonic sensor)*1 ON or OFF ON: Sound detected
OFF: Sound not detected
Only displays "ON" on the Data List once. When checking again, disconnect and reconnect the GTS.
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor Sound Detect
50003 123 273
NOTICE:

*1: Perform the intrusion sensor (theft warning ultrasonic sensor) operation inspection with the GTS disconnected.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION



g.

From inside the vehicle, put your hand in front of the intrusion sensor (theft warning ultrasonic sensor) and move it back and forth a distance of 0.3 m (0.984 ft.) and check the Data List.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Intrusion Sensor Detection status of the intrusion sensor (theft warning ultrasonic sensor) ON or OFF ON: Intrusion detected
OFF: Intrusion not detected
-
Body Electrical > Main Body > Data List
Tester Display
Intrusion Sensor
50003 123 204

OK:

The GTS display changes correctly in response to the detection condition of the intrusion sensor (theft warning ultrasonic sensor).


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)
2.CHECK INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)
a.

Using an oscilloscope, check the waveform.

E352022C15
3.542,0.313 3.99,0.563 0.448,0.25 4.281,1.875 3.771,1.385 true 1.906,2.823 1.594,2.708 false 2.438,2.854 2.229,2.708 false 2.427,0.354 2.688,0.583 0.26,0.229 10 false *a 1.406,2.615 1.698,2.833 0.292,0.219 10 false *b 2.052,2.615 2.323,2.844 0.271,0.229 10 false *c 3.99,2.625 4.302,2.781 0.313,0.156 10 false *d 3.99,3.156 4.302,3.313 0.313,0.156 10 false *e 2.115,3.219 2.385,3.438 0.271,0.219 10 false *f 2.51,3.198 2.813,3.417 0.302,0.219 10 false *g 2.667,3.625 2.979,3.781 0.313,0.156 10 false *h 1.51,4.135 1.792,4.365 0.281,0.229 10 false *i 4,4.125 4.313,4.354 0.313,0.229 10 false *j 4.375,1.813 4.823,2.01 0.448,0.198 10 false IOUT 1,2.479 1.292,2.698 0.292,0.219 10 false HI 1,2.917 1.292,3.135 0.292,0.219 10 false LO 3.656,0.354 4.104,0.573 0.448,0.219 10 false R17
*a Component with harness connected
(Intrusion Sensor (Theft Warning Ultrasonic Sensor))
*b IOUT Initial Signal
*c IOUT Initial Response *d Approximately 1.0 Second
*e Initial Diagnosis *f Approximately 1.0 to 1.6 Seconds
*g Approximately 0.05 Seconds *h Approximately 5.5 Seconds
*i Disarmed State *j Arming Preparation State


Measurement Condition:
Item Content
Tester Connection R17-2 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)


HINT:
·

If the intrusion sensor (theft warning ultrasonic sensor) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

·

If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).



OK:

The waveform is output properly (HI is 6.5 V or higher and LO is below 1 V).



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR))
a.

Disconnect the F16 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the R17 intrusion sensor (theft warning ultrasonic sensor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-12 (ISIF) - R17-2 (IOUT) Always Below 1 Ω
F16-12 (ISIF) or R17-2 (IOUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR