Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › ECM › from 2020.08
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295702 ECM A

2ZR-FXE ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Panoramic view monitor system (Click here)
for 2ZR-FXE

Replacement of ECM


Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the ECM has been struck or dropped, replace it.

·

Perform the Vehicle Identification Number (VIN) registration when replacing the ECM.

Click hereEngine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 89661 3.REMOVE ECM

a.
A375009C01
0.708,0.833 0.865,1.167 0.865,1.167 1.042,1.167 true 2.417,0.885 2.594,1.219 2.594,1.219 2.771,1.219 true 0.344,1.094 0.521,1.26 0.177,0.167 10 true *a 1.979,1.083 2.156,1.25 0.177,0.167 10 true *a 1.031,1.083 1.208,1.25 0.177,0.167 10 true *b 2.76,1.125 2.938,1.292 0.177,0.167 10 true *b
*a Push
*b Lock


Raise the 2 levers while pushing the locks on the levers, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



b.
A394191

Disengage the 2 clamps.


c.

Remove the bolt and separate the engine wire from the No. 1 ECM bracket.


d.
A394192C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, nut and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.



Hide 89667E 4.REMOVE NO. 1 ECM BRACKET

a.
A394193

Remove the 2 screws and No. 1 ECM bracket from the ECM.


Hide 89668 5.REMOVE NO. 2 ECM BRACKET

a.
A394194

Remove the 2 screws and No. 2 ECM bracket from the ECM.