Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › ENGINE COOLANT TEMPERATURE SENSOR › from 2020.08
RM32K0E _51 Engine / Hybrid System _060312 2ZR-FXE ENGINE CONTROL _0295707 ENGINE COOLANT TEMPERATURE SENSOR A

2ZR-FXE ENGINE CONTROL  ENGINE COOLANT TEMPERATURE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine coolant temperature sensor or No. 2 engine coolant temperature sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Panoramic view monitor system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2ZR-FXE (for Nickel Metal Hydride Battery):(Click here)
for 2ZR-FXE (for Lithium-ion Battery):(Click here)
for 2ZR-FXE

Replacement of engine coolant temperature sensor


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
for 2ZR-FXE

ECM


Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 2.DRAIN ENGINE COOLANT (for Engine)

Hide 82121 3.DISCONNECT ENGINE WIRE

a.
A394206

Remove the bolt to disconnect the engine wire.


Hide 89422 5.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

a.
A394207

Disconnect the engine coolant temperature sensor connector.


b.
A394208C01
2.865,2.385 3.083,2.698 false 1.771,0.688 1.99,1 true 2.667,2.313 2.979,2.51 0.313,0.198 10 false *1 1.396,0.594 1.74,0.781 0.344,0.188 10 true SST
*1 Gasket


Using SST, remove the engine coolant temperature sensor from the water outlet.

SST
09817-33191  

NOTICE:

If the engine coolant temperature sensor has been struck or dropped, replace it.



c.

Remove the gasket from the engine coolant temperature sensor.


Hide G9200 6.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 89422D 7.REMOVE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR

a.
A394209

Disconnect the No. 2 engine coolant temperature sensor connector.


b.
A394210

Remove the clip and No. 2 engine coolant temperature sensor from the No. 2 water by-pass pipe.

NOTICE:

If the No. 2 engine coolant temperature sensor has been struck or dropped, replace it.