The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
The vehicle has a hybrid system that operates at voltages up to 650 V. The hybrid system uses an HV battery that contains an electrolyte which is a strong alkali solution that includes potassium hydroxide. Be sure to follow the instructions in this manual to handle the system correctly. Failure to do so may result in serious injury or electrocution.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
3. DISCHARGE FUEL SYSTEM PRESSURE
4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
5.SECURE STEERING WHEEL ASSEMBLY
6.REMOVE FRONT WHEELS
51441
7.REMOVE NO. 1 ENGINE UNDER COVER
Remove the 4 bolts, 4 screws, 4 clips and No. 1 engine under cover from the vehicle.
51444A
8.REMOVE REAR ENGINE UNDER COVER LH
Remove the 6 clips and rear engine under cover LH from the vehicle.
51443C
9.REMOVE REAR ENGINE UNDER COVER RH
Remove the 6 clips and rear engine under cover RH from the vehicle.
10.DRAIN ENGINE OIL
11.DRAIN ENGINE COOLANT (for Engine)
12.DRAIN HYBRID TRANSAXLE FLUID
16296
13.DISCONNECT NO. 8 WATER BY-PASS HOSE
Slide the clip and disconnect the No. 8 water by-pass hose from the No. 2 water by-pass hose assembly.
53141F
14.REMOVE RADIATOR COVER
except GR SPORT:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (except GR SPORT)>REMOVAL
for GR SPORT:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for GR SPORT)>REMOVAL
17752
15.REMOVE NO. 2 AIR CLEANER INLET
22210
16.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
17801
17.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17701
18.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
17771A
19.REMOVE AIR CLEANER BRACKET
17751
20.REMOVE NO. 1 AIR CLEANER INLET
G9200
21.REMOVE INVERTER WITH CONVERTER ASSEMBLY
33820B
22.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.
Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.
Remove the bolt to disconnect the transmission control cable assembly from the cylinder head cover sub-assembly.
16573B
23.DISCONNECT NO. 3 RADIATOR HOSE
Remove the 2 bolts from the hybrid vehicle transaxle assembly.
Slide the clip and disconnect the No. 3 radiator hose from the water outlet.
16572D
24.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clip and disconnect the No. 2 radiator hose from the water inlet sub-assembly.
87246
25.DISCONNECT OUTLET HEATER WATER HOSE
Slide the clip and disconnect the outlet heater water hose from the No. 1 water by-pass pipe.
87245A
26.DISCONNECT INLET HEATER WATER HOSE A
Slide the clip and disconnect the inlet heater water hose A from the EGR pipe with cooler sub-assembly.
23826
27.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
Slide the clip and disconnect the No. 1 fuel vapor feed hose from the fuel vapor feed pipe.
23901
28.DISCONNECT FUEL TUBE SUB-ASSEMBLY
G922H
29.DISCONNECT INLET HYBRID RADIATOR HOSE
Slide the clip and disconnect the inlet hybrid radiator hose from the motor cooling cooler.
G922F
30.DISCONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE
Slide the clip and disconnect the outlet No. 1 hybrid water pump hose from the motor cooling cooler.
88703
31.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
88704
32.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
82123
33.DISCONNECT NO. 3 ENGINE WIRE
Disengage the clamp.
Remove the 2 bolts and disconnect the No. 3 engine wire from the hybrid vehicle transaxle assembly.
45259A
34.REMOVE COLUMN HOLE COVER SILENCER SHEET
45260
35.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45025D
36.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
58166
37.REMOVE FRONT FLOOR COVER LH
58165B
38.REMOVE FRONT FLOOR COVER RH
Use the same procedure as for the LH side.
57533B
39.REMOVE FRONT FLOOR CENTER BRACE
17410
40.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
41.REMOVE FRONT DRIVE SHAFT ASSEMBLY
51108A
42.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
51107A
43.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
44.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.
Remove the bolt and No. 2 engine mounting stay LH.
Remove the 6 bolts to separate the front suspension crossmember sub-assembly from the vehicle.
Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
45.REMOVE WIRE HARNESS CLAMP BRACKET (w/o Differential Pressure Sensor)
Disengage the 3 clamps.
Remove the bolt and wire harness clamp bracket from the cylinder head sub-assembly.
89481B
46.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ Differential Pressure Sensor)
25715
47.REMOVE EMISSION CONTROL VALVE BRACKET (w/ Differential Pressure Sensor)
Disengage the 3 clamps.
Remove the bolt and emission control valve bracket from the cylinder head sub-assembly.
48.INSTALL ENGINE HANGERS
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| *3 | Bolt |
Install the No. 1 engine hanger and No. 2 engine hanger with the 2 bolts.
| No. 1 Engine Hanger | 12281-37021 |
| No. 2 Engine Hanger | 12282-37011 |
| Bolt | 91552-81050 |
Using an engine sling device and engine lifter, secure the engine assembly with transaxle.
Adjust the angle of the sling device carefully to prevent damage or deformation to the engine hangers or engine assembly.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
12372A
49.REMOVE ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Remove the 4 bolts, nut and engine mounting insulator LH from the vehicle.
12305
50.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Remove the 2 bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH and vehicle.
Remove the bolt, nut and disconnect the air conditioner tube and accessory assembly.
Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.
88370
51.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY
28193
52.REMOVE STARTER HOLE INSULATOR
11363A
53.REMOVE FLYWHEEL HOUSING SIDE COVER
82121
54.REMOVE ENGINE WIRE
Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.
55.REMOVE ENGINE ASSEMBLY
31270
56.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY
13405
57.REMOVE FLYWHEEL SUB-ASSEMBLY
58.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine assembly to an engine stand.
59.REMOVE ENGINE HANGERS
Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.