Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HV BATTERY STACK (for LITHIUM-ION BATTERY) › from 2020.08
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404396 HV BATTERY STACK(for LITHIUM-ION BATTERY) A

2ZR-FXE HYBRID / BATTERY CONTROL  HV BATTERY STACK(for LITHIUM-ION BATTERY)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV supply stack sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedures not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
·

Replacement of No. 1 HV supply stack sub-assembly

·

Replacement of No. 2 HV supply stack sub-assembly


1.

Prediagnostic battery charge

2.

Battery diagnosis

3.

Battery status info update


HV battery status information cannot be updated (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

·

The hybrid system has high-voltage circuits. Accidents, such as electric shock, or electric leaks may result if the hybrid system is not operated in a correct manner. Make sure to follow the correct procedure.

·

When disposing of an HV battery assembly or hybrid vehicle supply stack sub-assembly, make sure to return them through an authorized collection agent who is capable of handling them safely.

·

Before returning an HV battery assembly, make sure to perform a recovery inspection.

·

Before returning an HV supply stack sub-assembly, make sure to perform a recovery inspection.

·

Make a note of the output DTCs as some of them may be necessary for "Recovery Inspection" of the HV battery assembly and HV supply stack sub-assemblies.



NOTICE:

When replacing the No. 1 hybrid vehicle supply stack sub-assembly or No. 2 hybrid vehicle supply stack sub-assembly, it is necessary to check, adjust and equalize the SOC of the HV battery. Otherwise, the engine may run longer than normal, resulting in a decrease in fuel efficiency.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HV BATTERY STACK (for LITHIUM-ION BATTERY)>BASIC INSPECTION


HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 2. READ VALUE USING GTS

a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid Battery Temperature 1 to 6.

Powertrain > HV Battery > Data List
Tester Display
Hybrid Battery Temperature 1
Hybrid Battery Temperature 2
Hybrid Battery Temperature 3
Hybrid Battery Temperature 4
Hybrid Battery Temperature 5
Hybrid Battery Temperature 6
50003 398 62,63,64,65,66,67

d.

Read the Data List.

NOTICE:

If any of the temperatures listed in "Hybrid Battery Temperature 1 to 6" are 50°C or more, leave the vehicle until the temperature drops to less than 50°C.



Hide G920L 4.REMOVE UPPER NO.1 HYBRID BATTERY COVER SUB-ASSEMBLY

Hide G92Z0 5.REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY WITH NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Hide G92D1 7.REMOVE NO. 1 HYBRID BATTERY INTAKE DUCT

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375938

Disengage the claw of hybrid battery thermistor (sensor portion) and disconnect the hybrid battery thermistor from the No. 1 hybrid battery intake duct.


b.

Remove the clip and No. 1 hybrid battery intake duct from the HV battery.


Hide G920Q 9.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375940

Disengage the clamp.


b.

Remove the nut and No. 1 hybrid battery shield sub-assembly from the HV battery.


Hide G92PC 10.REMOVE NO. 1 HV BATTERY PROTECTOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375941

Disengage the clamp to disconnect the wire harness.


b.
A375942

Remove the 3 nuts.


c.

Disengage the 2 claws and remove the No. 1 HV battery protector from the No. 2 HV battery protector.


Hide G9508 13.REMOVE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375949

Disconnect the connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.
A375950

Disconnect the connector.


c.
A375951

Disengage the claw.


d.
A375952

Remove the 4 nuts and No. 1 HV supply stack sub-assembly.


Hide G9509 14.REMOVE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A375953

Disengage the claw.


b.
A375954

Remove the 4 nuts and No. 2 HV supply stack sub-assembly.


Hide 15.PERFORM RECOVERY INSPECTION

a.

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HV BATTERY STACK (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION