Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HV BATTERY (for LITHIUM-ION BATTERY) › from 2020.08
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404392 HV BATTERY(for LITHIUM-ION BATTERY) A

2ZR-FXE HYBRID / BATTERY CONTROL  HV BATTERY(for LITHIUM-ION BATTERY)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV battery removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedures not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Replacement of HV battery
1.

Prediagnostic battery charge

2.

Battery diagnosis

3.

Battery status info update


HV battery status information cannot be updated (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

If the HV battery has been struck or dropped, replace it.

·

When connecting a connector to the HV battery, confirm that the connector is securely connected through the following:

- Push the connector until a click sound is heard.

- Visually check and confirm that the connector is securely connected by pulling on it.

·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·

When performing repairs around the HV battery, such as using a tap, do not allow metal shavings to enter the HV battery.

·

Do not touch any high voltage wire harnesses, connectors or parts with bare hands.

·
A375893

Hold the areas shown in the illustration and lift the HV battery.

·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts or nuts of the HV battery.

·
A375891C02
0.938,2.26 0.365,1.5 0.365,1.5 0.719,0.906 false 0.167,1.417 0.479,1.615 0.313,0.198 10 false *a
*a Opening


Do not put your hands into the openings of the HV battery.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

Do not climb on top of or stand on the HV battery.

·

Do not allow any foreign matter or water to enter the HV battery.

·

If any bolts, nuts or clips are dropped into the HV battery, make sure to remove them.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 2. READ VALUE USING GTS

a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid Battery Temperature 1 to 6.

Powertrain > HV Battery > Data List
Tester Display
Hybrid Battery Temperature 1
Hybrid Battery Temperature 2
Hybrid Battery Temperature 3
Hybrid Battery Temperature 4
Hybrid Battery Temperature 5
Hybrid Battery Temperature 6
50003 398 62,63,64,65,66,67

d.

Read the Data List.

NOTICE:

If any of the temperatures listed in "Hybrid Battery Temperature 1 to 6" are 50°C or more, leave the vehicle until the temperature drops to less than 50°C.



Hide 7.INSTALL CONNECTOR COVER ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.


a.
A376294C08
2.063,1.417 2.313,1.615 0.25,0.198 10 true *a 1.875,0.5 2.125,0.698 0.25,0.198 10 true *b
*a Bolt (A)
*b Bolt (B)


Using a T25 "TORX" socket wrench, install the connector cover assembly to the inverter with converter assembly with the bolt (A).

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)

NOTICE:
·

Do not touch the waterproof seal of the connector cover assembly.

·

Do not allow any foreign matter or water to enter the inverter with converter assembly.




b.

Install the bolt (B).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 9.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 10.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 67918A 11.REMOVE REAR DOOR SCUFF PLATE LH

Hide 76974F 12.REMOVE REAR UNDER SIDE COVER LH

Hide 67917A 13.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 76973F 14.REMOVE REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 76971G 15.REMOVE REAR UNDER COVER

a.
A375870

Disengage the 2 clips.


b.

Disengage the 2 guides to remove the rear under cover from the rear seat cushion leg sub-assembly.


Hide 71033 16.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

a.
A375872

Remove the 9 bolts and rear seat cushion leg sub-assembly.


Hide G9230 17.REMOVE BATTERY COOLING BLOWER ASSEMBLY

Hide G92N4A 18.REMOVE NO. 1 HV BATTERY COVER PANEL RH

CAUTION:

Be sure to wear insulated gloves.


a.
A375875C02
1.292,0.25 1.594,0.25 false 1.25,1.26 1.552,1.26 false 1.125,1.115 1.292,0.885 1.292,0.885 1.448,0.885 true 0.698,0.938 0.896,0.938 0.896,0.938 1.063,0.729 false 1.646,0.167 1.958,0.365 0.313,0.198 10 false *1 1.604,1.198 1.917,1.396 0.313,0.198 10 false *2 0.5,0.552 0.813,0.75 0.313,0.198 10 false *b 0.521,0.854 0.833,1.052 0.313,0.198 10 false *a 1.51,0.813 1.823,1.01 0.313,0.198 10 false *c
*1 Service Plug Grip
*2 Battery Cover Lock Striker
*a Projection
*b Turn
*c Button


Using the service plug grip, remove the battery cover lock striker.

HINT:

Insert the projection of the service plug grip and turn the button of the battery cover lock striker counterclockwise to release the lock.



b.

Remove the 2 bolts, 3 nuts and No. 1 HV battery cover panel RH from the HV battery.


Hide 821H1 19.DISCONNECT HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A450902C01
1.917,1.229 2.292,1.229 true 2.313,1.135 2.563,1.354 0.25,0.219 10 true *a
*a Shield Ground


Disconnect the 2 HV battery junction block assembly connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.

Disconnect the shield ground from the HV battery.


Hide 82161 20.DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A375882

Disengage the clamp.


b.

Disconnect the electric vehicle battery plug assembly connector.


c.

Disconnect the HV battery junction block assembly connector.


Hide G9290A 21.REMOVE HYBRID BATTERY HOSE ASSEMBLY

a.
A375884

Disconnect the hybrid battery hose assembly from the vehicle.


b.

Disengage the 2 claws to remove the hybrid battery hose assembly from the HV battery.


Hide G92PF 22.REMOVE NO. 4 HV BATTERY PROTECTOR

CAUTION:

Be sure to wear insulated gloves.


a.
A375886

Disengage the 2 claws to remove the No. 4 HV battery protector from the HV battery.


Hide 82161 23.DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A375888

Disengage the clamp.


b.

Disconnect the HV battery connector.


Hide G9510 24.REMOVE HV BATTERY

CAUTION:

Be sure to wear insulated gloves.


a.
A378150

Remove the 4 bolts and HV battery from the vehicle.

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to remove it. When removing the HV battery, be careful not to damage the parts around it.

·

When removing the HV battery from the vehicle, do not allow it to contact the vehicle.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

Insulate the disconnected terminals or connectors with insulating tape.

·

If the HV battery has been struck or dropped, replace it.




Hide 25.PERFORM RECOVERY INSPECTION

a.

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HV BATTERY (for LITHIUM-ION BATTERY)>RECOVERY INSPECTION