The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear door window frame moulding removal/installation are shown below.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
75740
1.REMOVE REAR DOOR BELT MOULDING ASSEMBLY
67872
2.REMOVE REAR DOOR WEATHERSTRIP
75076
3.REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY
When removing the rear door outside moulding sub-assembly, heat the vehicle body and rear door outside moulding sub-assembly using a heat light.
| Item | Temperature |
|---|---|
| Rear Door Outside Moulding Sub-assembly | 40 to 60°C (104 to 140°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the vehicle body or rear door outside moulding sub-assembly excessively.
Using a heat light, heat the rear door outside moulding sub-assembly.
| *a | Double-sided Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Protective Tape |
Apply protective tape around the rear door outside moulding sub-assembly as shown in the illustration.
Using a moulding remover D, disengage the clip and guide, and separate the double-sided tape and caulking sponge to remove the rear door outside moulding sub-assembly as shown in the illustration.
75764A
4.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING
Insert a 4.0 mm (0.157 in.) drill bit into a drill.
| *a | Tape |
Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
| Area | Measurement |
|---|---|
| A | 5.0 mm (0.197 in.) |
Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.
Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 5 rivets.
Be careful of the drilled rivets, as they may be hot.
Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
Prying the rivets with the drill may damage the rivet installation holes or drill bit.
Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.
Disengage the guides to remove the rear door upper window frame moulding.
75766A
5.REMOVE REAR DOOR REAR WINDOW FRAME MOULDING
Insert a 4.0 mm (0.157 in.) drill bit into a drill.
| *a | Tape |
Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
| Area | Measurement |
|---|---|
| A | 5.0 mm (0.197 in.) |
Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.
Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 2 rivets and rear door rear window frame moulding.
Be careful of the drilled rivets, as they may be hot.
Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
Prying the rivets with the drill may damage the rivet installation holes or drill bit.
Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.