Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR BELT MOULDING › from 2020.08
RM32K0E _59 Vehicle Exterior _061792 EXTERIOR PANELS / TRIM _0304179 REAR DOOR BELT MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR BELT MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear door belt moulding removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
·

Door glass

·

Door glass run


Initialize Power Window Control System
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 69284D 3.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 74272A 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Hide 67498 5.REMOVE REAR DOOR REAR FRAME BRACKET

Hide 67604 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 68199 7.REMOVE REAR DOOR BELT REAR SEAL

Hide 68174A 8.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP

Hide 68197 9.REMOVE REAR DOOR BELT SEAL

Hide 67872 10.DISCONNECT REAR DOOR WEATHERSTRIP

a.

Disconnect the rear door weatherstrip until the screw of the door window rear lower sub-assembly is visible.


Hide 67842E 11.REMOVE REAR DOOR SERVICE HOLE COVER

Hide 67408F 12.REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY

Hide 68104 13.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Hide 67674A 14.REMOVE REAR DOOR FRAME GARNISH

Hide 68152C 15.REMOVE REAR DOOR GLASS RUN

Hide 68124B 16.REMOVE REAR DOOR QUARTER WINDOW GLASS

Hide 75740 17.REMOVE REAR DOOR BELT MOULDING ASSEMBLY

a.
B458684C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear door belt moulding assembly.


b.
B458685C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear door belt moulding assembly as shown in the illustration.