Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2020.08
RM32K0E _58 Vehicle Interior _061839 PRE-COLLISION _0303861 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U023587  Lost Communication with Cruise Control Front Distance Range Sensor Missing Message  


DESCRIPTION

The millimeter wave radar sensor assembly is connected to the skid control ECU (brake booster with master cylinder assembly) via the CAN communication line.

When entering test mode, if the skid control ECU (brake booster with master cylinder assembly) determines that the pre-collision system is not installed, the millimeter wave radar sensor assembly stores DTC U023587.

DTC No. Detection Item DTC Detection Condition Trouble Area
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Missing Message In test mode, when the skid control ECU (brake booster with master cylinder assembly) has determined that the pre-collision system is not installed in the vehicle.
·

Electronically Controlled Brake System

·

Millimeter Wave Radar Sensor Assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT




PROCEDURE

1.CHECK ELECTRONICALLY CONTROLLED BRAKE SYSTEM
a.

Check the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If U023587 is output in the pre-collision system, electronically controlled brake system DTCs may also have been output. Check the electronically controlled brake system first.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.TEST MODE INSPECTION (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

B

2.TEST MODE INSPECTION (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

When entering test mode, the skid control ECU (brake booster with master cylinder assembly) communicates with the millimeter wave radar sensor assembly to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit test mode within 5 seconds of entering test mode.


a.

Procedure to Enter Test Mode

i.

Turn the ignition switch to ON.


ii.

Check that the steering wheel is centered.


iii.

Check that the parking brake is released.


iv.

Check that the shift lever is in P.


v.

Turn the power switch off.


vi.

Connect the GTS to the DLC3.


vii.

Turn the power switch on (IG).


viii.

Turn the GTS on.


ix.

Switch the skid control ECU (brake booster with master cylinder assembly) to Test Mode using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 4359

x.

Check that the ABS warning, brake system warning light (yellow indicator) and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.

HINT:
·

If the ABS warning, brake system warning light (yellow indicator) and slip indicator lights do not blink, inspect the ABS warning, brake system warning light (yellow indicator) and slip indicator light circuits.

·

Do not exit test mode within 5 seconds of entering test mode. If test mode is exited within 5 seconds of entering test mode, DTC U023587 may be stored. If DTC U023587 is output after exiting test mode, enter test mode again, wait at least 5 seconds, then recheck for DTCs.





Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Pre-Collision System > Clear DTCs
50002 432

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Pre-Collision System > Trouble Codes
50001 432

Result:
Result Proceed to
U023587 is not output A
U023587 is output B



A

END

B

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY