Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Skid Control (ABS/VSC/TRC)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Skid Control (ABS/VSC/TRC)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Skid Control (ABS/VSC/TRC)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Brake booster with master cylinder assembly branch line or connector

·

Power source circuit of brake booster with master cylinder assembly

·

Brake booster with master cylinder assembly ground circuit

·

Brake booster with master cylinder assembly



WIRING DIAGRAM

for LHD



C366175E04
1.667,1.042 1.917,1.208 0.25,0.167 10 false 13 1.667,0.521 1.917,0.688 0.25,0.167 10 false 3 0.26,1.521 0.677,1.688 0.417,0.167 10 false F116 0.26,1.688 2.26,1.938 2,0.25 10 false No. 4 CAN Junction Connector 0.26,3.125 0.677,3.292 0.417,0.167 10 false F113 0.26,3.281 2.26,3.531 2,0.25 10 false No. 2 CAN Junction Connector 1.646,2.125 1.896,2.292 0.25,0.167 10 false 5 1.656,2.646 1.906,2.813 0.25,0.167 10 false 16 5.531,0.531 5.781,0.698 0.25,0.167 10 false 43 5.531,1.052 5.781,1.219 0.25,0.167 10 false 42 5.521,2.125 5.771,2.292 0.25,0.167 10 false 30 5.51,2.677 5.76,2.844 0.25,0.167 10 false 29 5.51,3.708 5.76,3.875 0.25,0.167 10 false 15 5.573,4.25 5.823,4.417 0.25,0.167 10 false 5 5.521,4.792 5.771,4.958 0.25,0.167 10 false 23 5.583,5.313 5.833,5.479 0.25,0.167 10 false 9 5.521,5.875 5.771,6.042 0.25,0.167 10 false 26 5.531,6.406 5.781,6.573 0.25,0.167 10 false 39 5.833,0.625 6.333,0.792 0.5,0.167 10 false CA1H 5.833,1.146 6.333,1.313 0.5,0.167 10 false CA1L 5.833,2.24 6.333,2.406 0.5,0.167 10 false CA2H 5.833,2.75 6.333,2.917 0.5,0.167 10 false CA2L 5.844,3.813 6.344,3.979 0.5,0.167 10 false +BI1 5.844,4.375 6.344,4.542 0.5,0.167 10 false +BI2 5.833,4.906 6.333,5.073 0.5,0.167 10 false IG1 5.833,5.438 6.333,5.604 0.5,0.167 10 false IG2 5.833,5.969 6.333,6.135 0.5,0.167 10 false GND1 5.833,6.51 6.333,6.677 0.5,0.167 10 false GND2 5.333,6.844 5.833,7.01 0.5,0.167 10 false A39 5.333,7 7,7.417 1.667,0.417 10 false Brake Booster with Master Cylinder Assembly 4.313,5.583 5.396,5.75 1.083,0.167 10 false ECU-IG2 NO. 3 4.333,5.042 5.417,5.208 1.083,0.167 10 false ECU-IG1 NO. 2 4.458,4.5 5.542,4.667 1.083,0.167 10 false ABS NO. 3 4.469,3.958 5.552,4.125 1.083,0.167 10 false ABS NO. 2 2.188,3.792 3.604,4.042 1.417,0.25 10 false from Auxiliary Battery 2.198,4.333 3.615,4.583 1.417,0.25 10 false from Auxiliary Battery 2.208,4.865 3.625,5.115 1.417,0.25 10 false from IG1-NO. 1 Relay 2.219,5.396 3.635,5.646 1.417,0.25 10 false from IG2-NO. 2 Relay

for RHD



C366174E05
1.667,0.531 1.906,0.771 0.24,0.24 10 false 2 1.667,1.073 1.906,1.313 0.24,0.24 10 false 13 1.656,1.594 1.896,1.833 0.24,0.24 10 false 9 1.656,2.146 1.979,2.302 0.323,0.156 10 false 20 0.26,2.656 0.75,2.823 0.49,0.167 10 false F115 0.26,2.823 2.26,3.073 2,0.25 10 false No. 4 CAN Junction Connector 5.521,0.531 5.76,0.771 0.24,0.24 10 false 43 5.521,1.083 5.76,1.323 0.24,0.24 10 false 42 5.521,1.615 5.76,1.854 0.24,0.24 10 false 30 5.51,2.167 5.75,2.406 0.24,0.24 10 false 29 5.521,3.219 5.76,3.458 0.24,0.24 10 false 15 5.583,3.75 5.823,3.99 0.24,0.24 10 false 5 5.531,4.302 5.771,4.542 0.24,0.24 10 false 23 5.583,4.833 5.823,5.073 0.24,0.24 10 false 9 5.521,5.375 5.76,5.615 0.24,0.24 10 false 26 5.51,5.927 5.75,6.167 0.24,0.24 10 false 39 5.844,0.646 6.333,0.813 0.49,0.167 10 false CA1H 5.844,1.188 6.333,1.354 0.49,0.167 10 false CA1L 5.833,1.729 6.323,1.896 0.49,0.167 10 false CA2H 5.823,2.26 6.313,2.427 0.49,0.167 10 false CA2L 5.833,3.344 6.323,3.51 0.49,0.167 10 false +BI1 5.833,3.844 6.323,4.01 0.49,0.167 10 false +BI2 5.833,4.417 6.323,4.583 0.49,0.167 10 false IG1 5.844,4.917 6.333,5.083 0.49,0.167 10 false IG2 5.833,5.49 6.333,5.656 0.5,0.167 10 false GND1 5.844,6.01 6.344,6.177 0.5,0.167 10 false GND2 5.344,6.333 5.844,6.5 0.5,0.167 10 false A39 5.344,6.5 7.01,6.917 1.667,0.417 10 false Brake Booster with Master Cylinder Assembly 4.323,5.073 5.406,5.24 1.083,0.167 10 false ECU-IG2 NO. 3 4.344,4.531 5.427,4.698 1.083,0.167 10 false ECU-IG1 NO. 2 4.458,4.021 5.542,4.188 1.083,0.167 10 false ABS NO. 3 4.458,3.469 5.542,3.635 1.083,0.167 10 false ABS NO. 2 2.177,3.313 3.677,3.563 1.5,0.25 10 false from Auxiliary Battery 2.198,3.823 3.698,4.073 1.5,0.25 10 false from Auxiliary Battery 2.177,4.365 3.677,4.615 1.5,0.25 10 false from IG1-NO. 1 Relay 2.177,4.906 3.677,5.156 1.5,0.25 10 false from IG2-NO. 2 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

e.

Check that DTC C1241 which indicates a malfunction in the power source circuit of the electronically controlled brake system is not stored by the electronically controlled brake system.


Result:
Result Proceed to
DTC C1241 is not output A
DTC C1241 is output B



A

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSTIC PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the brake booster with master cylinder assembly connector.


c.
C349830C16
1.542,0.146 1.958,0.417 0.417,0.271 1.646,1.667 1.896,0.667 true 1.521,1.656 1.25,0.667 true 1.302,2.594 1.5,1.958 true 1.833,2.583 1.646,1.948 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.646,0.219 1.958,0.417 0.313,0.198 10 false A39 1.948,0.542 2.5,0.823 0.552,0.281 10 false CA2H 0.885,0.51 1.438,0.792 0.552,0.281 10 false CA2L 1,2.625 1.552,2.906 0.552,0.281 10 false CA1L 1.802,2.615 2.354,2.896 0.552,0.281 10 false CA1H
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-43 (CA1H) - A39-42 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A39-30 (CA2H) - A39-29 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349830C17
1.542,0.104 1.958,0.375 0.417,0.271 1.708,1.281 1.5,0.594 true 1.521,1.531 1.208,0.76 true 2.104,1.281 2.25,0.51 true 2.656,1.448 2.833,0.667 true 2.083,2.583 2.271,1.583 true 2.833,2.583 2.667,1.729 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.646,0.156 1.958,0.354 0.313,0.198 10 false A39 1.177,0.448 1.74,0.75 0.563,0.302 10 false +BI2 0.896,0.646 1.448,0.927 0.552,0.281 10 false +BI1 1.917,2.615 2.469,2.896 0.552,0.281 10 false IG1 2.833,2.625 3.385,2.906 0.552,0.281 10 false GND2 2.313,0.344 2.865,0.625 0.552,0.281 10 false IG2 2.927,0.563 3.385,0.771 0.458,0.208 10 false GND1
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-26 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A39-39 (GND2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-5 (+BI2) - Body ground Power switch off 11 to 14 V
A39-15 (+BI1) - Body ground Power switch off 11 to 14 V
A39-9 (IG2) - Body ground Power switch on (IG) 11 to 14 V
A39-23 (IG1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)