Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Battery ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Battery ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "HV Battery" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "HV Battery" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "HV Battery" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Battery ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Battery ECU assembly branch line or connector

·

Power source circuit of battery ECU assembly

·

Battery ECU assembly ground circuit

·

Battery ECU assembly



WIRING DIAGRAM

C348699E07
0.365,2.094 3.271,2.292 2.906,0.198 10 false No. 6 Junction Connector 0.365,1.917 0.802,2.135 0.438,0.219 10 false M104 1.729,1.438 2.104,1.656 0.375,0.219 10 false 14 1.76,0.854 2.135,1.073 0.375,0.219 10 false 3 5.396,0.844 5.771,1.063 0.375,0.219 10 false 9 5.396,1.438 5.771,1.656 0.375,0.219 10 false 1 5.677,0.99 6.146,1.25 0.469,0.26 10 false CA2H 5.677,1.573 6.052,1.792 0.375,0.219 10 false CA2L 5.396,2.344 5.771,2.563 0.375,0.219 10 false 8 5.688,2.479 6.063,2.698 0.375,0.219 10 false AM 5.344,3.167 5.719,3.385 0.375,0.219 10 false 16 5.677,3.313 6.115,3.531 0.438,0.219 10 false IGCT 4.01,2.302 4.906,2.531 0.896,0.229 10 false ECU-B NO. 1 4.021,3.135 4.833,3.365 0.813,0.229 10 false IGCT NO. 2 1.708,2.448 3.292,2.792 1.583,0.344 10 false from Auxiliary Battery 2.021,3.281 3.208,3.635 1.188,0.354 10 false from IGCT Relay 5.396,3.615 5.771,3.833 0.375,0.219 10 false 4 5.688,3.76 6.063,3.979 0.375,0.219 10 false GND 5.344,3.99 5.719,4.208 0.375,0.219 10 false 10 5.688,4.125 6.135,4.375 0.448,0.25 10 false GND1 5.25,4.792 5.625,5.01 0.375,0.219 10 false z22 5.563,4.792 7.083,5.146 1.521,0.354 10 false Battery ECU Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (BATTERY ECU ASSEMBLY BRANCH LINE)
a.
C349826C07
1.531,0.385 1.948,0.656 0.417,0.271 0.969,1.833 0.729,0.885 true 0.646,2.885 0.979,2.135 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.479,2.917 0.979,3.125 0.5,0.208 10 false CA2H 0.354,0.698 0.854,0.906 0.5,0.208 10 false CA2L 1.635,0.458 2.135,0.667 0.5,0.208 10 false z22
*a Front view of wire harness connector
(to Battery ECU Assembly)


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the z15 battery ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z22-9 (CA2H) - z22-1 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BATTERY ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C349826C08
1.531,0.385 1.948,0.656 0.417,0.271 2.51,1.833 2.729,0.896 true 0.688,2.854 1.25,2.146 true 2.635,2.875 2.438,2.146 true 1.573,1.844 1.25,0.948 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.906,0.792 1.406,1 0.5,0.208 10 false GND 1.635,0.458 2.135,0.667 0.5,0.208 10 false z22 0.51,2.896 1.01,3.104 0.5,0.208 10 false GND1 2.75,0.729 3.073,0.958 0.323,0.229 10 false AM 2.573,2.906 3.073,3.115 0.5,0.208 10 false IGCT
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z22-4 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
z22-10 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z22-8 (AM) - Body ground Power switch off 11 to 14 V
z22-16 (IGCT) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)