Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32K0E _57 Power Source / Network _059857 NETWORKING _0293867 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Headlight ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Headlight ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Headlight swivel (AFS)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Headlight swivel (AFS)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Headlight swivel (AFS)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "AFS ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Headlight ECU sub-assembly LH branch line or connector

·

Power source circuit of Headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly LH ground circuit

·

Headlight ECU sub-assembly LH



WIRING DIAGRAM

C366185E15
1.615,0.531 1.76,0.729 0.146,0.198 10 false 3 1.625,1.073 1.844,1.281 0.219,0.208 10 false 14 0.083,1.542 0.438,1.75 0.354,0.208 10 false F114 0.073,1.698 2,1.917 1.927,0.219 10 false No. 3 CAN Junction Connector 2.188,2.188 3.531,2.396 1.344,0.208 10 false from IG1-NO. 1 Relay 2.281,2.729 3.531,2.938 1.25,0.208 10 false from H-LP LH Relay 4.344,2.375 5.313,2.583 0.969,0.208 10 false ECU-IG1 NO. 3 5.583,3.698 6.708,3.896 1.125,0.198 10 false A95*1, A100*2 5.563,3.875 6.833,4.281 1.271,0.406 10 false Headlight ECU Sub-assembly LH 5.531,0.531 5.75,0.74 0.219,0.208 10 false 24 5.531,1.073 5.75,1.281 0.219,0.208 10 false 23 5.604,2.146 5.823,2.354 0.219,0.208 10 false 4 5.542,2.667 5.76,2.875 0.219,0.208 10 false 13 5.531,3.219 5.75,3.427 0.219,0.208 10 false 12 5.813,0.604 6.24,0.813 0.427,0.208 10 false CANH 5.802,1.156 6.229,1.365 0.427,0.208 10 false CANL 5.792,2.219 6.219,2.427 0.427,0.208 10 false IG 5.792,2.75 6.219,2.958 0.427,0.208 10 false ECUB 5.792,3.302 6.219,3.51 0.427,0.208 10 false GND 0.427,3.781 3.031,3.979 2.604,0.198 10 false *1: for TMMT Made 0.438,4.208 3.042,4.406 2.604,0.198 10 false *2: for TMC Made

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the power switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (HEADLIGHT ECU SUB-ASSEMBLY LH BRANCH LINE)
a.
C308332C39
1.875,0.167 2.375,0.417 0.5,0.25 0.875,0.167 1.375,0.417 0.5,0.25 2.833,1.833 2.635,1.354 true 2.25,1.833 2.458,1.354 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.01,0.219 1.469,0.417 0.458,0.198 10 false A95 2.667,1.865 3.281,2.063 0.615,0.198 10 false CANH 2.083,1.865 2.698,2.063 0.615,0.198 10 false CANL 1.948,0.208 2.406,0.406 0.458,0.198 10 false A100 1.458,0.219 1.833,0.5 0.375,0.281 12 false *A 2.438,0.208 2.813,0.49 0.375,0.281 12 false *B
*A for TMMT Made
*B for TMC Made
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMF Made:
Tester Connection Condition Specified Condition
A95-24 (CANH) - A95-23 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

for TMC Made:
Tester Connection Condition Specified Condition
A100-24 (CANH) - A100-23 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (HEADLIGHT ECU SUB-ASSEMBLY LH)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMT Made:
Tester Connection Condition Specified Condition
A95-12 (GND) - Body ground Always Below 1 Ω

for TMC Made:
Tester Connection Condition Specified Condition
A100-12 (GND) - Body ground Always Below 1 Ω



b.
C308332C40
1.906,0.167 2.406,0.417 0.5,0.25 1,0.167 1.5,0.417 0.5,0.25 2.083,1.833 1.833,1.229 true 1.5,1.833 1.281,1.302 true 0.583,1.833 0.823,1.302 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 1.135,0.208 1.594,0.406 0.458,0.198 10 false A95 1.344,1.854 1.958,2.052 0.615,0.198 10 false ECUB 0.448,1.854 1.063,2.052 0.615,0.198 10 false GND 2.052,1.854 2.365,2.052 0.313,0.198 10 false IG 2.01,0.219 2.469,0.417 0.458,0.198 10 false A100 1.583,0.219 1.958,0.5 0.375,0.281 12 false *A 2.479,0.219 2.854,0.5 0.375,0.281 12 false *B
*A for TMMT Made
*B for TMC Made
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for TMMT Made:
Tester Connection Switch Condition Specified Condition
A95-4 (IG) - Body ground Power switch on (IG) 11 to 14 V
A95-13 (ECUB) - Body ground Power switch on (IG) 11 to 14 V

for TMC Made:
Tester Connection Switch Condition Specified Condition
A100-4 (IG) - Body ground Power switch on (IG) 11 to 14 V
A100-13 (ECUB) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)