Home › Brake › BRAKE (REAR) › REAR BRAKE (for TMMT Made) › from 2020.08
RM32K0E _54 Brake _060047 BRAKE (REAR) _0407397 REAR BRAKE(for TMMT Made) A

BRAKE (REAR)  REAR BRAKE(for TMMT Made)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C366010C03
0.99,1.927 1.51,1.5 true 0.979,1.927 1.49,1.448 true 0.823,1.854 1.135,2.01 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks of the rear disc and rear axle hub and bearing assembly, and install the rear disc.

NOTICE:

When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



Hide 2.INSTALL REAR DISC BRAKE CYLINDER MOUNTING

a.

Install the rear disc brake cylinder mounting to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)


Hide 3.INSTALL REAR DISC BRAKE BUSHING DUST BOOT

a.
C399996C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



b.

Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.


Hide 4.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C399997C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the rear No. 1 disc brake cylinder slide pin.


b.

Install a new rear disc brake cylinder slide bushing to the rear No. 1 disc brake cylinder slide pin.


c.
C399998C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin.


d.
C399542C01
2.583,1.667 2.458,1.417 true 2.313,0.531 2.188,0.281 true 2.583,1.708 2.833,1.917 0.25,0.208 10 true *1 2.323,0.583 2.521,0.823 0.198,0.24 10 true *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear No. 2 Disc Brake Cylinder Slide Pin


Install the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin to the rear disc brake cylinder mounting.


e.

Push the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin into each rear disc brake bushing dust boot to engage the pins to the boots.


Hide 5.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

a.

Install the 4 rear disc brake pad support plates to the rear disc brake cylinder mounting.

NOTICE:

Be sure to install each rear disc brake pad support plate in the correct position and direction.



Hide 6.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM

Hide 7.INSTALL REAR DISC BRAKE PAD

a.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.



Hide 8.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C399999C01
1.156,2.646 1.469,2.802 0.313,0.156 10 false *a 1.906,2.552 2.219,2.708 0.313,0.156 10 false *b
*a Hold
*b Turn


Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 new bolts in the order shown in the illustration.

Torque:
34.5 N*m (352 kgf*cm, 25 ft.*lbf)


Hide 46310B 9.INSTALL PARKING BRAKE ACTUATOR ASSEMBLY

a.

Apply a light coat of lithium soap base glycol grease to a new O-ring.


b.

Install the O-ring to the rear disc brake cylinder assembly.

NOTICE:

Make sure to replace the O-ring with a new one when installing the parking brake actuator assembly.



c.

Using a 5 mm hexagon socket wrench, install the parking brake actuator assembly to the rear disc brake cylinder assembly with the 2 bolts.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)


Hide 890C0A 10.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.

Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.


Hide 47319F 11.CONNECT REAR FLEXIBLE HOSE

a.

Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.



Hide 12. BLEED BRAKE LINE

Hide 13.BLEED REAR DISC BRAKE CYLINDER ASSEMBLY

CAUTION:

If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder.


NOTICE:
·

Perform air bleeding while maintaining the brake fluid level between the MAX and MIN lines on the brake fluid reservoir.

·

Do not allow brake fluid to contact any painted surface. If brake fluid leaks onto any painted surface, immediately wash it off.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

While performing air bleeding of the rear disc brake assembly, the bolt can be reused during the bleeding procedure. After air bleeding is complete, replace the bolt with a new one.



a.

Perform the procedure to enter rear disc brake pad replacement mode 5 times.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>TEST MODE PROCEDURE


b.

Release the parking brake.


c.
C399528

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.


d.

Remove the center No. 1 cowl top ventilator louver.

Click hereGeneral>MAINTENANCE>BRAKE FLUID>REPLACEMENT


e.

Remove the brake master cylinder reservoir filler cap.


f.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

NOTICE:
·

Make sure that there is sufficient brake fluid in the reservoir.

·

If brake fluid leaks onto any painted surface, immediately wash it off.

·

Do not remove the filter from the brake master cylinder reservoir and be sure to fill the brake master cylinder reservoir with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.




g.
C400000C01
1.917,2.552 2.229,2.708 0.313,0.156 10 false *a 1.146,2.667 1.458,2.823 0.313,0.156 10 false *b
*a Turn
*b Hold


Remove the bolt and separate the rear disc brake cylinder assembly.(*1)

NOTICE:

Keep the rear no. 2 disc brake cylinder slide pin free of foreign matter.



h.
C400004

Hold the rear disc brake cylinder assembly horizontally, then tilt it 45° toward the bleeder plug side as shown in the illustration.(*2)


i.
C400031C01
1.906,2.573 2.219,2.729 0.313,0.156 10 false *a 1.125,2.677 1.438,2.833 0.313,0.156 10 false *b
*a Turn
*b Hold


Temporarily install the rear disc brake cylinder assembly with the bolt.(*3)


j.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.(*4)


k.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.(*5)


l.

Repeat steps (*1) through (*5) 3 times.

NOTICE:

If there is still air in the system after performing steps (*1) through (*5) 3 times, repeat the steps (*1) through (*5) until the air has been bled.



m.

Tighten the bleeder plug completely.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


n.

Install the rear disc brake cylinder assembly with a new bolt.

Torque:
34.5 N*m (352 kgf*cm, 25 ft.*lbf)


o.

Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.


p.

Inspect for brake fluid leaks.


q.

Inspect the brake fluid level in the reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION


r.

Install the brake master cylinder reservoir filler cap assembly.


s.

Install the center No. 1 cowl top ventilator louver.

Click hereGeneral>MAINTENANCE>BRAKE FLUID>REPLACEMENT


Hide 14.INSTALL REAR WHEEL

Hide 16. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART