Home › Vehicle Interior › SEAT BELT › OCCUPANT DETECTION SENSOR › from 2020.08
RM32K0E _58 Vehicle Interior _062271 SEAT BELT _0303946 OCCUPANT DETECTION SENSOR A

SEAT BELT  OCCUPANT DETECTION SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the occupant detection sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

CAUTION:
·
B458500

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·
B407261

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL


Hide 73230 2.REMOVE FRONT SEAT INNER BELT ASSEMBLY

Hide 71073S 3.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 72494 4.REMOVE VERTICAL ADJUSTING HANDLE (w/ Vertical Adjuster)

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 72537 5.REMOVE RECLINING HINGE OUTER COVER

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 72525A 6.REMOVE RECLINING ADJUSTER RELEASE HANDLE

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 71848A 7.REMOVE SEAT ADJUSTER COVER CAP (w/ Vertical Adjuster)

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 71811D 8.REMOVE FRONT SEAT CUSHION SHIELD

Hide 71861 9.REMOVE FRONT SEAT INNER CUSHION SHIELD

Hide 10.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 11.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 71511S 12.REMOVE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)

a.

Using a screwdriver, disengage the claws to remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.

B459877C01
1.479,2.563 1.813,2.438 true 1.854,2.323 2.167,2.479 0.313,0.156 10 false *a
*a Screwdriver - -