Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat) › from 2020.08
RM32K0E _58 Vehicle Interior _061825 SEAT _0404433 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front seat assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

CAUTION:
·
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·
B407261

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:

If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.


HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the driver side and front passenger side.

·

The procedure listed below is for the driver side.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
·
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



Hide 71910A 2.REMOVE FRONT SEAT HEADREST ASSEMBLY

a.

Remove the front seat headrest assembly from the front seat assembly.


Hide 72124 3.REMOVE FRONT OUTER SEAT TRACK BRACKET COVER

a.

Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.


b.
B453918

Disengage the claws to remove the front outer seat track bracket cover.


Hide 72128A 4.REMOVE FRONT INNER SEAT TRACK BRACKET COVER

a.
B453919

Disengage the claws to remove the front inner seat track bracket cover.


Hide 72138 5.REMOVE OUTER SEAT TRACK COVER

a.

Operate the seat track adjusting handle and move the front seat assembly to the foremost position.


b.
B453920

Disengage the claws and guide to remove the outer seat track cover.


Hide 72158 6.REMOVE INNER SEAT TRACK BRACKET COVER

a.
B453921

Disengage the claws and guide to remove the inner seat track bracket cover.


Hide 7.REMOVE FRONT SEAT ASSEMBLY

a.
B453922

Using a T50 "TORX" socket wrench, remove the 2 bolts on the rear side of the front seat assembly.


b.

Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.


c.
B453923

Using a T50 "TORX" socket wrench, remove the 2 bolts on the front side of the front seat assembly.


d.

Operate the seat track adjusting handle and move the front seat assembly to the center position.


e.

Operate the reclining adjuster release handle and move the seatback to the upright position.


f.

Disconnect the front seat airbag assembly connector under the front seat assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.
B279750C24
1.781,1.052 2.281,1.052 true 1.948,1.49 2.448,1.49 false 1.146,1.406 1.646,1.406 true 2.323,0.979 2.5,1.156 0.177,0.177 10 false *a 2.5,1.406 2.677,1.583 0.177,0.177 10 false *b 0.865,1.313 1.135,1.563 0.271,0.25 10 false (A)
*a White Housing Lock
*b Yellow CPA
V100135

Slide


Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)


ii.

Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.




g.

Disconnect each connector and disengage each clamp under the front seat assembly.


h.
B453924

Remove the front seat assembly as shown in the illustration.

NOTICE:
·

2 or more people are required when carrying the front seat assembly out of the vehicle.

·

Protect the front seat leg.

·

Be careful not to damage the front seat assembly, body exterior or body interior.