Home › Engine / Hybrid System › M20A-FXS (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2020.08
RM32K0E _51 Engine / Hybrid System _083957 M20A-FXS INTAKE / EXHAUST _0404362 INTAKE MANIFOLD A

M20A-FXS INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL VACUUM HOSE

a.

Install the vacuum hose to the intake manifold.


Hide 17177 2.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.

Install a new No. 1 intake manifold to head gasket to the intake manifold.


Hide 17111 3.INSTALL INTAKE MANIFOLD

a.

Set the intake manifold.

HINT:

At this time, do not install the parts with bolts or nuts.



b.
A432885N01
1.635,1.292 1.792,1.49 0.156,0.198 10 true 1 0.781,0.323 0.938,0.521 0.156,0.198 10 true 2 0.281,0.552 0.438,0.75 0.156,0.198 10 true 4 2.438,0.135 2.594,0.333 0.156,0.198 10 true 3 3.104,0.396 3.26,0.594 0.156,0.198 10 true 5

Temporarily install the intake manifold and No. 2 fuel delivery guard to the cylinder head sub-assembly with the 4 bolts and 2 nuts.


c.

Tighten the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


d.

Tighten the bolt.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 17138B 4.INSTALL INTAKE MANIFOLD STAY

a.
A432884N01
1.573,1.542 1.729,1.74 0.156,0.198 10 true A 2.573,0.76 2.729,0.958 0.156,0.198 10 true B

Engage the guide to install the intake manifold stay.


b.

Install the bolt (B).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Using an 8 mm socket wrench, install the bolt (A).

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Engage the clamp to connect the HV air conditioning wire to the No. 1 water hose clamp bracket.


Hide 5.INSTALL BRACKET

a.
A432882C01
0.708,1.177 1.021,1.469 true 2.677,0.781 2.99,1.073 true 3.052,1.021 3.271,1.198 0.219,0.177 10 true *1 0.438,1.042 0.646,1.229 0.208,0.188 10 true *2
*1 Wire Harness Clamp Bracket
*2 No. 2 Water Hose Clamp Bracket


Install the No. 2 water hose clamp bracket to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Using an 8 mm socket wrench, install the wire harness clamp bracket to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16264D 6.CONNECT NO. 2 WATER BY-PASS HOSE

a.

Engage the clamp to connect the No. 2 water by-pass hose to the No. 2 water hose clamp bracket.


Hide 16279 7.CONNECT NO. 3 WATER BY-PASS PIPE

a.

Using an 8 mm socket wrench, connect the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.


Hide 8.CONNECT ENGINE WIRE

a.
A432879

Engage the clamp to connect the engine wire to the intake manifold.


b.

Connect the engine wire to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A432878

Engage the 3 clamps to connect the engine wire to the intake manifold and fuel vapor feed pipe.


d.

Connect the engine wire to the fuel delivery guard, intake manifold and timing chain cover assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Connect the 2 connectors.


f.

Connect the fuel vapor feed hose to the No. 1 vacuum switching valve assembly.


Hide 23827D 9.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Engage the clamp to connect the No. 1 fuel vapor feed hose.


b.

Connect the No. 1 fuel vapor feed hose to the intake manifold and slide the hose clip to secure it.


Hide 89421 10.INSTALL E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Hide 25601 11.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 22030 12.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 17751 13.INSTALL NO. 1 AIR CLEANER INLET