Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM › from 2020.12
RM32K0E _53 Suspension _061172 TIRE / WHEEL _0299377 TIRE AND WHEEL SYSTEM G

TIRE / WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Inspect the tires for wear and proper inflation pressure.

Cold Tire Inflation Pressure:
Tire Size Cold Tire Inflation Pressure
Front Rear
215/60R17 96H 230 kPa (2.3 kgf/cm2, 33 psi) 230 kPa (2.3 kgf/cm2, 33 psi)
225/50R18 95V 230 kPa (2.3 kgf/cm2, 33 psi) 230 kPa (2.3 kgf/cm2, 33 psi)
225/45R19 92W 230 kPa (2.3 kgf/cm2, 33 psi) 230 kPa (2.3 kgf/cm2, 33 psi)
225/45R19 96W 230 kPa (2.3 kgf/cm2, 33 psi) 230 kPa (2.3 kgf/cm2, 33 psi)


Cold Tire Inflation Pressure (for Compact Spare Tire):
Tire Size Cold Tire Inflation Pressure
T145/90D16 106M 420 kPa (4.2 kgf/cm2, 60 psi)
T145/70D18 107M 420 kPa (4.2 kgf/cm2, 60 psi)



ii.

Tire pressure adjustment method when warm:

1.

Turn the power switch off.

2.

Connect the GTS to the DLC3.

3.

Turn the power switch on (IG).

4.

Turn the GTS on.

5.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

6.

Adjust the tire pressure so that the displayed value is equal to the set pressure.

7.

Perform initialization and check that initialization completes.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION

8.

Check and record the value of the Data List item "Temperature in Tire". (Ts)

9.

Check and record the ambient temperature during tire pressure adjustment. (Tm)

10.

Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)

HINT:

Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P

P = (Specified Pressure) + (Ts - Tm)


11.

Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".


NOTICE:
for ECE-R64 Type:

If the tire pressure is decreased approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more in order to adjust the tire pressure, even if the adjusted tire pressure is 80% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 80% of the tire pressure set when the tires are warmed. In this case, perform initialization again.




b.
C137874

Using a dial indicator, check the runout of the tires.

Maximum Tire Runout:

1.4 mm (0.0551 in.)


HINT:

Measure the runout with the wheel assembly removed from the vehicle.



Hide 2. ROTATE TIRES

a.

Remove the wheel assembly.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>REMOVAL


b.

for TMC Made 19 Inch Wheel:

i.
C196349C01
0,0 0,0 false
V100135

Front


Rotate the tires as shown in the illustration.



c.

except TMC Made 19 Inch Wheel:

i.
C143305C02
2.896,0.396 3.146,0.573 0.25,0.177 10 false A 2.896,1.458 3.146,1.635 0.25,0.177 10 false B
V100135

Front


If the spare tire uses a different type of wheel than the other tires, rotate the tires as shown by (A) in the illustration. If the spare tire has the same type of wheel as the other tires, rotate the tires, including the spare tire, as shown by (B) in the illustration.



d.

Install the wheel assembly.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>INSTALLATION



Hide 3.INSPECT AND ADJUST WHEEL BALANCE

a.

for TMC Made 19 Inch Wheel:

i.
C202467C01
0.597,3.514 0.825,3.655 0.228,0.142 10 *a 2.084,3.668 2.312,3.810 0.228,0.142 10 *a
*a 25 mm (0.984 in.)


Inspect and adjust the off-the-car balance.

Maximum Wheel Imbalance:

8.0 g (0.0176 lb)


NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

·

Do not touch the adhesive surface of the balance weight.

·

Adhere a stick-on type balance weight to the flat surface*a shown in the illustration.

·

Push the balance weight with your finger to securely adhere it to the desired position.

·

Do not reuse balance weights.

·

Use only TOYOTA genuine stick-on type balance weights or equivalent.



HINT:
·

Use stick-on type balance weights for both the inner and outer side.

·

If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.





b.

except TMC Made 19 Inch Wheel:

i.
C144018C01
2.052,3.667 2.281,3.823 0.229,0.156 10 false *a
*a 25 mm (0.984 in.)


Inspect and adjust the off-the-car balance.

Maximum Wheel Imbalance:

8.0 g (0.0176 lb)


NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

·

Do not touch the adhesive surface of the balance weight.

·

Adhere a stick-on type balance weight to the flat surface*a shown in the illustration.

·

Push the balance weight with your finger to securely adhere it to the desired position.

·

Do not reuse balance weights.

·

Use only TOYOTA genuine stick-on type balance weights or equivalent.



HINT:
·

Use clip-on type balance weights for the inner side, and stick-on type balance weights for the outer side.

·

If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.