The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub and bearing assembly on-vehicle inspection are shown below.
When removing or installing the front disc brake caliper assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C1214 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this step.
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISABLE BRAKE CONTROL
for TMC Made:
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMC Made)>REMOVAL
for TMMT Made:
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for TMMT Made)>REMOVAL
3.REMOVE REAR WHEEL
4.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY
42431
5.REMOVE REAR DISC
for TMC Made:
Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMC Made)>REMOVAL
for TMMT Made:
Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMMT Made)>REMOVAL
6.INSPECT REAR AXLE HUB BEARING LOOSENESS
Using a dial indicator, check for looseness near the center of the rear axle hub.
0.05 mm (0.00196 in.)
Ensure that the dial indicator is set perpendicular to the measurement surface.
Keep the magnet of the dial indicator away from the rear axle hub and bearing assembly.
If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.
7.INSPECT REAR AXLE HUB RUNOUT
Using a dial indicator, check for runout on the surface of the rear axle hub outside the rear axle hub bolts.
0.05 mm (0.00196 in.)
Ensure that the dial indicator is set perpendicular to the measurement surface.
Make sure to install the tip of the dial indicator towards the outside of the rear axle hub bolts.
Keep the magnet of the dial indicator away from the rear axle hub and bearing assembly.
If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.
42431
8.INSTALL REAR DISC
for TMC Made:
Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMC Made)>INSTALLATION
for TMMT Made:
Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMMT Made)>INSTALLATION
9.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY
10.INSTALL REAR WHEEL
11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Connect the reservoir level switch connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION
Turn the power switch on (READY).
Depress the brake pedal and release it.
Clear the DTCs.
12. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART