Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › MOTOR GENERATOR CONTROL COMPUTER › from 2020.08
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0469036 MOTOR GENERATOR CONTROL COMPUTER A

M20A-FXS HYBRID / BATTERY CONTROL  MOTOR GENERATOR CONTROL COMPUTER  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>M20A-FXS (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
A309734

·

If metal shavings are created when bolts are removed from the inverter with converter assembly, remove them using tape or equivalent.

·

Use non-residue type tape.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide G9200 1.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 33829E 2.REMOVE TRANSMISSION CONTROL CABLE SUPPORT

Hide 4. VERIFY THAT VOLTAGE OF INVERTER WITH CONVERTER IS 0 V

CAUTION:

Wear insulating gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.
A393897C01
2.188,0.719 2.51,0.229 2.51,0.229 2.802,0.229 true 2.844,0.125 3.156,0.323 0.313,0.198 10 false *a
*a Tape


Remove the protective tape from the HV floor under wire opening.


b.
A393898C01
0.281,2.5 0.927,2.5 true 1.375,2.51 2.229,2.51 true 0.104,2.385 0.417,2.583 0.313,0.198 10 false *a 2.271,2.417 2.583,2.615 0.313,0.198 10 false *a
*a Voltage Measurement Position


Using a voltmeter, measure the voltage between the high voltage cable connector terminals.

Standard voltage:

0V


HINT:
·

Use measuring range of DC 750 V or more on the voltmeter.

·

If it is confirmed that high-voltage is not being applied to the inverter with converter assembly, the following procedures can be performed without using insulated tools or gloves.




c.

Apply protective tape to the area that was exposed.

NOTICE:

Use non-residue type tape.



Hide G9200 5.CLEAN INVERTER WITH CONVERTER ASSEMBLY

a.

Using a piece of cloth, clean the outside of the inverter with converter assembly and around the bolts.

NOTICE:

To prevent foreign matter from entering the inverter with converter assembly, make sure that the protective tape is not partially removed.



Hide 6. HOW TO PREVENT STATIC ELECTRICITY

SST
09890-47010  

NOTICE:
·

Static electricity should be eliminated when removing/installing the inverter with converter assembly.

·

Do not touch the electronic components of a circuit board.

·

Keep clothes away from electronic components.

·

Place the inverter with converter assembly and any removed electronic components on SST (antistatic mat).



a.
E104190N03
1.104,0.448 0.615,0.302 0.615,0.302 2.125,0.156 true 0.313,0.24 0.792,0.604 0.479,0.365 10 false SST

Wear an antistatic wrist strap.


b.

Connect the ground clip of the antistatic mat securely to a ground point provided in the workshop or on a workbench (anchor bolt).

HINT:

If the ground clip cable is too short, use an extension cable.



c.

Connect the ground clip of the antistatic wrist strap securely to the specified point of the antistatic mat.


d.

When handling internal components of the inverter with converter assembly, use only antistatic gloves or bare hands to prevent damage from static electricity or the entry of foreign matter.


Hide G9221 7.REMOVE INVERTER UPPER COVER

a.
A480052

Remove the 10 bolts.


b.

Using a screwdriver with its tip wrapped with protective tape, remove the inverter upper cover from the inverter with converter assembly.

A480053C01
4.167,1.677 4.25,1.844 4.25,1.844 4.417,1.844 true 1.5,2.229 1.583,2.396 1.583,2.396 1.75,2.396 true 1.083,5.115 1.167,5.281 1.167,5.281 1.333,5.281 true 3.167,2 3.333,2 3.333,2 3.5,1.833 true 6.417,5.167 6.583,5.167 6.583,5.167 6.667,4.833 true 3.25,6.833 3.417,6.833 3.417,6.833 3.5,6.5 true 4.469,1.781 4.719,1.948 0.25,0.167 10 true *a 1.802,2.333 2.052,2.5 0.25,0.167 10 true *a 1.385,5.219 1.635,5.385 0.25,0.167 10 true *a 2.969,1.948 3.219,2.115 0.25,0.167 10 true *a 3.042,6.771 3.292,6.938 0.25,0.167 10 true *a 6.208,5.115 6.458,5.281 0.25,0.167 10 true *a 4.406,5.188 4.563,5.385 0.156,0.198 10 true 1 1.875,3.51 2.031,3.708 0.156,0.198 10 false 2 4.354,2.979 4.51,3.177 0.156,0.198 10 false 3 2.031,4.01 2.188,4.208 0.156,0.198 10 false 5 5.156,3.396 5.313,3.594 0.156,0.198 10 false 6 2.917,2.875 3.073,3.073 0.156,0.198 10 false 4
*a Protective Tape - -



c.

Using a screwdriver with its tip wrapped with protective tape, remove the inverter upper cover from the inverter with converter assembly.

NOTICE:
·
A480086C02
0.406,0.313 0.719,0.51 0.313,0.198 12 false *a 0.469,2.698 0.781,2.896 0.313,0.198 12 false *b
*a OK
*b NG


Do not damage the sealing surfaces of the inverter with converter assembly.

·

Do not touch or allow grease or oil to contact the sealing surfaces of the inverter with converter assembly.

·

Be careful not to damage the sealing surfaces of the inverter with converter assembly.

·

To prevent internal components of the inverter with converter assembly from being damaged, do not insert the screwdriver excessively.



HINT:
A480054

I f the upper inverter panel is difficult to remove, place a screwdriver in a gap under the upper inverter cover and remove.



Hide 8.REMOVE SEAL PACKING FROM INVERTER WITH CONVERTER ASSEMBLY

NOTICE:
·

Do not allow any removed seal packing to enter the inverter with converter assembly.

·

Do not touch the circuit board.

·

Do not allow any moisture to come into contact.



a.

Using a finger, remove any seal packing that has seeped into the inverter with converter assembly.

HINT:

Make sure to remove any seal packing which has seeped toward the inside of inverter with converter assembly before installing the seal packing removal cover, otherwise the seal packing may be pushed into the inverter with converter assembly.



b.
A480055

Break off the seal packing removal cover and scraper at each break off line.


c.

Set the seal packing removal cover on the inverter with converter assembly and secure it by lightly pressing it at the 2 areas shown in the illustration.

A480056C02
0.5,0.573 0.813,0.729 0.313,0.156 10 false *a 5.083,0.573 5.396,0.729 0.313,0.156 10 false *b 2.781,0.583 2.938,0.781 0.156,0.198 10 false A 2.781,1.167 2.938,1.365 0.156,0.198 10 true A 4.542,1.5 4.698,1.698 0.156,0.198 10 false B 3.635,1.469 3.792,1.667 0.156,0.198 10 true B
*a A-A Cross Section *b B-B Cross Section
V100155

Push - -


NOTICE:

Make sure that the seal packing removal cover is in secure contact with the inside surface of the inverter with converter assembly without any gaps.



d.
A480057C02
2,0.781 2.167,0.365 2.167,0.365 2.417,0.365 true 2.469,0.302 2.885,0.635 0.417,0.333 10 false *a
*a MG Connector Opening


Place the inverter with converter assembly on its side on an antistatic mat as shown in the illustration.

NOTICE:
·

Make sure that the MG connector opening in the inverter with converter assembly is facing upward.

·

Make sure that the inverter with converter assembly is oriented correctly, otherwise seal packing may enter the inverter with converter assembly.




e.

Using a scraper, remove any remaining seal packing from the inverter with converter assembly.

NOTICE:
·

It is not necessary to remove small amounts of seal packing which are not easily scraped off.

A393901C02
2.24,0.958 2.479,0.76 2.479,0.76 2.844,0.76 true 4.5,0.938 4.74,0.74 4.74,0.74 5.146,0.74 true 4.375,1.365 4.615,1.167 4.615,1.167 4.979,1.167 true 1.865,0.083 2.094,0.24 0.229,0.156 10 false *a 4.167,0.083 4.396,0.24 0.229,0.156 10 false *b 2.115,1.542 2.344,1.698 0.229,0.156 10 false *c 4.448,1.563 4.677,1.719 0.229,0.156 10 false *c 2.906,0.688 3.219,0.885 0.313,0.198 10 false *d 5.198,0.656 5.51,0.854 0.313,0.198 10 false *e 5.021,1.083 5.333,1.281 0.313,0.198 10 false *f
*a Correct *b Incorrect
*c Width of Sealing Surface *d Difficult to Remove Seal Packing
*e Peeled Off Seal Packing *f Seal Packing Remaining on Full Width of Sealing Surface


·
A396292

Make sure to use the scraper supplied with the seal packing removal cover.



HINT:

Use the small end of the scraper to remove seal packing from small areas such as bolt holes.



f.

Using a clean piece of cloth, clean the sealing surfaces of the inverter with converter assembly.

NOTICE:
·

Do not use compressed air or a vacuum cleaner to clean the sealing surfaces of the inverter with converter assembly.

·

Do not use non-residue solvent to clean the sealing surfaces of the inverter with converter assembly.




g.
A480058

Remove the seal packing removal cover.

NOTICE:

Make sure that the inverter with converter assembly is oriented correctly, otherwise seal packing may enter the inverter with converter assembly when removing the seal packing removal cover.



h.

Check for and remove any foreign matter which has entered the inverter with converter assembly.


i.

Set the inverter with converter assembly upright.


j.

Clean the seal packing removal cover.

HINT:

As the seal packing removal cover will be reused, it is necessary to clean it to prevent foreign matter from entering the inverter with converter assembly and prevent damage.



Hide 04899L 9.REMOVE MOTOR GENERATOR CONTROL ECU KIT

CAUTION:

To prevent foreign matter from entering the inverter with converter assembly, once the seal packing removal cover has been removed, work cannot be suspended until the motor generator control ECU kit is reinstalled.


NOTICE:
·

Do not touch the circuit board.

·

Do not allow any foreign matter or water to enter the inverter with converter assembly.



a.

Install the seal packing removal cover to the inverter with converter assembly.

HINT:

The seal packing removal cover is installed to help prevent the motor generator control computer kit from being damaged if a part or tool is dropped on it.



b.
A480059

Install the 2 guide pins by hand at the positions shown in the illustration.

NOTICE:

Make sure that the guide pins are tightened securely.



c.
A480060

Remove the seal packing removal cover.


d.
A480061C02
0,0 0,0 false
V100136

Unlock
V100144

Rib


Check that the 4 screws of the circuit board replacement jig are unlocked, and then while holding the circuit board replacement jig by the ribs, align it with the guide pins and set it on the inverter with converter assembly.

HINT:

Make sure that circuit board replacement jig is perfectly level with the sealing surface.



e.
A480062C03
2.354,1.604 3.021,1.604 true 0.438,1.604 1.104,1.604 true 2.323,0.583 2.99,0.583 true 0.26,0.583 0.927,0.583 true 2,2.094 2.313,2.25 0.313,0.156 10 false *a 3.073,1.552 3.323,1.719 0.25,0.167 10 false *b 0.26,1.552 0.51,1.719 0.25,0.167 10 false *b 3.063,0.521 3.313,0.688 0.25,0.167 10 false *b 0.094,0.521 0.344,0.688 0.25,0.167 10 false *b
*a Locked
*b Knob
V100135

Bolt
V100136

Lock


Secure the circuit board replacement jig with the 2 bolts supplied with the circuit board replacement jig.

NOTICE:

Tighten the bolt by hand until the head contacts the jig.



f.

Lock the 4 screws as shown in the illustration to secure the circuit board replacement jig to the circuit board.

NOTICE:

When locking the screws of the circuit board replacement jig, do not apply excessive force to the screws, otherwise the circuit board replacement jig may be damaged.


HINT:

Make sure that the screws of the circuit board replacement jig are securely locked.



g.

Turn the 4 knobs of the circuit board replacement jig clockwise and secure the 4 screws of the circuit board replacement jig.


h.
A480063C02
1.75,3.875 1.5,3.792 1.5,3.792 1.167,3.792 true 2.969,2.083 2.885,2.083 2.885,2.083 2.719,2.417 true 2,2.167 2.25,2.333 0.25,0.167 10 true *a 1.333,3.5 1.583,3.667 0.25,0.167 10 true *b 0.979,3.74 1.229,4.073 0.25,0.333 10 false *c 3.021,2.021 3.354,2.188 0.333,0.167 10 false SST
*a Connected Vibration Dampening Connector
*b Disconnected Vibration Dampening Connector
*c Stopper of The Circuit Board Replacement Jig


Using SST, release the lock of each vibration dampening connector and raise the 28 vibration dampening connectors until they reach the stopper of the circuit board replacement jig.

SST
09905-00040  

NOTICE:

When disconnecting the vibration dampening connectors, release the lock of each connector with SST and then carefully lift the connector the specified amount.


HINT:
A393903C02
0.813,1.813 1.302,1.813 false 0.51,1.75 0.969,1.948 0.458,0.198 10 false SST

·

To prevent the vibration dampening connectors from being pulled up excessively, use both hands to raise them slowly as shown in the illustration.

·

The position of the lock will vary depending on the position of the vibration dampening connector. Refer to the arrows on the circuit board replacement jig.




i.
A480064C03
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Using the screwdriver supplied with the circuit board replacement jig, remove the 3 bolts (A).

HINT:

If the bolts are difficult to remove from the circuit board replacement jig, use a magnet hand.



j.

Using the screwdriver supplied with the circuit board replacement jig, remove the 13 bolts (B).

HINT:

If the bolts are difficult to remove from the circuit board replacement jig, use a magnet hand.



k.

Remove the 2 inverter upper cover installation bolts.


l.
A480065C02
0,0 0,0 false
V100144

Rib


While holding the circuit board replacement jig by the ribs, evenly lift the circuit board replacement jig and circuit board straight up and remove it.


m.
A480066

Place the circuit board replacement jig upside down on a clean workbench.


n.

Check that the terminals of the inverter with converter assembly are not bent or damaged and that it is free of foreign matter.

A393902C01
2.906,0.604 3.292,0.604 false 6.292,0.625 6.677,0.625 false 1.844,0.063 2.115,0.229 0.271,0.167 10 false *a 5.135,0.094 5.406,0.26 0.271,0.167 10 false *b 3.333,0.521 3.604,0.688 0.271,0.167 10 false *c 6.729,0.542 7,0.708 0.271,0.167 10 false *c
*a Correct *b Incorrect
*c Terminal - -


NOTICE:
·

Do not touch the terminals.

·

If any of the terminals are bent, replace the inverter with converter assembly with a new one. Do not attempt to repair the terminals.




o.

Turn the 4 knobs of the circuit board replacement jig counterclockwise and release the 4 screws of the circuit board replacement jig.

A480067C02
4.146,0.854 4.396,0.854 true 6.5,0.719 6.75,0.719 true 6.333,0.5 6.583,0.333 6.583,0.333 6.75,0.333 true 4.167,2.333 4.333,2.333 4.333,2.333 4.583,2 true 4.167,3.354 4.333,3.354 4.333,3.354 4.583,3.021 true 1.885,1.792 2.052,2.042 2.052,2.042 2.469,2.042 true 0.333,1.396 0.75,1.396 true 2.479,1.385 3.063,1.385 true 0.906,0.781 1.073,0.781 1.073,0.781 1.49,1.031 true 3.969,0.802 4.302,1.052 0.333,0.25 10 false *a 3.979,2.281 4.313,2.531 0.333,0.25 10 false *c 3.99,3.302 4.323,3.552 0.333,0.25 10 false *d 2.521,1.979 2.854,2.229 0.333,0.25 10 false *e 6.802,0.667 7.135,0.917 0.333,0.25 10 false *a 6.802,0.281 7.135,0.531 0.333,0.25 10 false *b 0.146,1.344 0.479,1.594 0.333,0.25 10 false *e 3.104,1.333 3.438,1.583 0.333,0.25 10 false *e 0.719,0.729 1.052,0.979 0.333,0.25 10 false *e
*a Hold here *b Do not hold here
*c Circuit Board *d Circuit Board Replacement Jig
*e Knob - -
V100135

Unlock - -



p.

Unlock the 4 circuit board replacement jig screws, and then while holding the sides of the circuit board or the top and bottom of the circuit board at the areas shown in the illustration, lift the circuit board to remove it from the circuit board replacement jig.

NOTICE:

Be careful not to touch any part of the circuit board other than the specified areas.