Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type with Single Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0522654 NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type)  B154711  GNSS Antenna Circuit Short to Ground  B154713  GNSS Antenna Circuit Open  


DESCRIPTION

These DTCs are stored when the radio and display receiver assembly detects an open or short in GNSS antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B154711 GNSS Antenna Circuit Short to Ground Short in GNSS antenna assembly
(2 trip detection logic)
·

Instr panel integration antenna assembly

·

Radio and display receiver assembly

·

Antenna cord sub-assembly

·

No. 5 antenna cord sub-assembly


B154713 GNSS Antenna Circuit Open Open in GNSS antenna assembly
(2 trip detection logic)
·

Instr panel integration antenna assembly

·

Radio and display receiver assembly

·

Antenna cord sub-assembly

·

No. 5 antenna cord sub-assembly



WIRING DIAGRAM

E469821E01
5.396,1.24 7.104,1.729 1.708,0.49 10 false Radio and Display Receiver Assembly 5.396,1.063 5.552,1.26 0.156,0.198 10 false A 2.156,0.667 2.417,0.833 0.26,0.167 10 false *2 0.063,1.167 1.417,1.583 1.354,0.417 10 false Instr Panel Integration Antenna Assembly 0.083,1.021 0.24,1.188 0.156,0.167 10 false D 1.156,0.427 1.313,0.625 0.156,0.198 10 false 3 5.906,0.427 6.063,0.625 0.156,0.198 10 false 1 2.583,2 5.167,2.333 2.583,0.333 10 false *1: Antenna Cord Sub-Assembly 3.75,0.365 3.917,0.531 0.167,0.167 10 false 1 3.333,0.365 3.5,0.531 0.167,0.167 10 false 1 4.99,0.667 5.25,0.833 0.26,0.167 10 false *1 3.313,0.552 3.479,0.719 0.167,0.167 10 false C 3.74,0.552 3.906,0.719 0.167,0.167 10 false B 2.583,2.417 5.167,2.75 2.583,0.333 10 false *2: No. 5 Antenna Cord Sub-Assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type with Single Knob Type)>PRECAUTION


PROCEDURE

1.INSPECT INSTR PANEL INTEGRATION ANTENNA ASSEMBLY

OK

2.INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE INSTR PANEL INTEGRATION ANTENNA ASSEMBLY

2.INSPECT NO. 5 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the instr panel integration antenna assembly connector.


b.

Disconnect the antenna cord sub-assembly connector.


c.
E469835C01
0.5,1.167 0.917,1.417 0.417,0.25 1.833,1.021 2.333,0.583 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.656,1.198 0.906,1.365 0.25,0.167 10 false D 2.385,0.479 2.635,0.646 0.25,0.167 10 false 3a
*a Component without harness connected
(to Instr Panel Integration Antenna Assembly)


E469823C01
0.583,1 1,1.25 0.417,0.25 1.417,0.833 1.75,0.333 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.74,1.031 0.99,1.198 0.25,0.167 10 false C 1.781,0.219 2.031,0.385 0.25,0.167 10 false 1a
*a Component without harness connected
(to Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-3 - C-1 Always Below 1 Ω
D-3a - C-1a Always Below 1 Ω
D-3a or C-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

3.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the No. 5 antenna cord sub-assembly connector.


b.

Disconnect the radio and display receiver assembly connector.


c.
E469823C02
0.583,1 1,1.25 0.417,0.25 1.417,0.833 1.75,0.333 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 0.74,1.031 0.99,1.198 0.25,0.167 10 false B 1.781,0.219 2.031,0.385 0.25,0.167 10 false 1a
*a Component without harness connected
(to No. 5 Antenna Cord Sub-Assembly)


E469836C01
1.896,1.5 2.333,1.167 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 2.365,1.073 2.615,1.24 0.25,0.167 10 false 1a
*a Component without harness connected
(to Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - A-1 Always Below 1 Ω
B-1a - A-1a Always Below 1 Ω
B-1a or A-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY