Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type with Single Knob Type) › from 2022.01
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0522654 NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type with Single Knob Type)  U11D087  Lost Local Communication with MET Missing Message  


DESCRIPTION

These DTC is stored when the radio and display receiver assembly detects a communication malfunction with the combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
U11D087 Lost Local Communication with MET Missing Message Communication malfunction between radio and display receiver assembly and combination meter assembly for 30 seconds or more
(2 trip detection logic)
·

Open or short in local bus circuit

·

Harness or connector

·

Combination meter assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E469833E01
0.135,1.344 1.76,1.625 1.625,0.281 10 false from Auxiliary Battery 0.125,2.167 1.552,2.469 1.427,0.302 10 false from IG2-NO. 2 Relay 1.979,1.542 3.177,1.74 1.198,0.198 10 false ECU-DCC NO. 2 3.156,1.25 3.396,1.469 0.24,0.219 10 false 40 3.188,2.063 3.427,2.281 0.24,0.219 10 false 39 3.417,1.365 3.656,1.583 0.24,0.219 10 false B 3.427,2.146 3.781,2.427 0.354,0.281 10 false IG+ 3.885,1.75 4.344,1.969 0.458,0.219 10 false MSCH 3.885,2.573 4.344,2.792 0.458,0.219 10 false MSCL 3.219,3.5 5.052,3.74 1.833,0.24 10 false Combination Meter Assembly 3.208,3.333 3.667,3.552 0.458,0.219 10 false F4 3.406,2.969 3.865,3.188 0.458,0.219 10 false ET 5.885,1.74 6.344,1.958 0.458,0.219 10 false CNH1 5.875,2.542 6.333,2.76 0.458,0.219 10 false CNL1 5.708,3.323 6.167,3.542 0.458,0.219 10 false F174 5.708,3.51 6.906,3.958 1.198,0.448 10 false Radio and Display Receiver Assembly 5.646,1.615 5.885,1.833 0.24,0.219 10 false 11 5.615,2.438 5.854,2.656 0.24,0.219 10 false 12 0.781,4.219 3.573,4.625 2.792,0.406 10 false : Local Bus Communication Line 4.344,1.604 4.802,1.823 0.458,0.219 10 false 36 4.344,2.427 4.802,2.646 0.458,0.219 10 false 37 3.177,2.854 3.635,3.073 0.458,0.219 10 false 21 2.073,2.292 2.969,2.594 0.896,0.302 10 false METER-IG2

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type with Single Knob Type)>PRECAUTION

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.

·

When replacing the combination meter assembly, make sure to replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in the combination meter assembly will not match the information from the vehicle and a DTC may be stored.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

·

When disconnecting the cable from the negative (-) auxiliary battery terminal, refer toGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:
·

Before disconnecting related connectors for inspection, push in on the connector body to check that each connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)
a.

Disconnect the F4 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-21 (ET) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F4-40 (B) - Body ground Always 11 to 14 V
F4-39 (IG+) - Body ground IG ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-36 (MSCH) - F4-37 (MSCL) Negative (-) auxiliary battery terminal disconnected 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR